DO
GUIDE
DOC. 7928B (2047266) 05.18
Specifications subject to change without notice.
8. Attach or slide the included hardware up onto the swivel mechanism tube in the order indicated in the illustration that follows step 9.
NOTE
: Orient the keyed metal washer tab to face away from the permanently installed limiting screw.
9. Adjust the tightness of the 7/8"-14 nut to achieve the desired swivel assembly motion resistance. Use a flat tool, such as a large flat-head
screwdriver, in the slot on the bottom of the swivel mechanism tube to hold the tube steady while tightening the nut.
Customize the Swivel Range
Reposition the two 8-32 x 1/8” screws placed on the swivel stop plate to customize the swivel range (330-degree rotation, maximum). Refer to the following
illustrations for details.
DO
Use the Security Option
Use the two included M3 x 0.5 x 6 mm screws to lock the touch screen to the TSW-560/760/1060-TTK.
1. Remove the two screws on the bottom of the unit that hold the metal bracket. Retain the metal bracket and screws.
2. Place the touch screen face down on a clean, soft cloth (not provided) and remove the two 1/2" long screws from the rear assembly. Retain these
screws to restore the touch panel without the security option, if necessary.
3. Secure the metal bracket to the rear assembly.
a. Position the bracket correctly (right side up, as shown above).
b. Secure the bracket with two included M3 x 0.5 x 6 mm screws. To prevent damage to threads, turn each screw counterclockwise until it
engages the thread.
c. Tighten the screws to 3 in/lb.
4. Secure the touch screen to the TSW-560/760/1060-TTK.
a. Connect the Ethernet cable to the touch screen while it remains face down.
b. Position the TSW-560/760/1060-TTK over the touch screen and gently pull any excess cable out through the rear of the tabletop accessory
until the two units come together.
c. Secure the TSW-560/760/1060-TTK to the touch screen with the two screws removed in step 1.
The specific patents that cover Crestron products are listed at
www.crestron.com/legal/patents
.
The product warranty can be found at
www.crestron.com/legal/sales-terms-conditions-warranties
.
Certain Crestron products contain open source software. For specific information, visit
www.crestron.com/legal/open-source-software
.
Crestron and the Crestron logo are either trademarks or registered trademarks of Crestron Electronics, Inc., in the United States and/or other countries. Other trademarks, registered trademarks,
and trade names may be used in this document to refer to either the entities claiming the marks and names or their products. Crestron disclaims any proprietary interest in the marks and names of
others. Crestron is not responsible for errors in typography or photography.
This document was written by the Technical Publications department at Crestron.
©2018 Crestron Electronics, Inc.
DO
Learn More
Visit the website for additional information and the latest firmware updates.
To learn more about this product, use a QR reader application on your
mobile device to scan the QR image.
Crestron Electronics
15 Volvo Drive, Rockleigh, NJ 07647
888.CRESTRON | www.crestron.com
Swivel mechanism tube
Slot in tube
Table or mounting surface (front edge)
Mounting holes (6)
in swivel stop plate
Screws (2) 8-32 x 1/8"
Bottom side of table or mounting surface
Screws (6) 8-8B x 1/2"
Cork and rubber washer
Keyed metal washer
Rubber washer
Steel washer
Nut 7/8"-14
Mounting hole
Permanently installed limiting screw
Swivel stop plate
Remove
these
screws.
Screws (2)
M3 x 0.5 x 6 mm
Metal
bracket
TSW-560-TTK
TSW-760-TTK
TSW-1060-TTK
TSW-560/760/1060-SMK
Keyed metal
washer tab
where swivel
motion starts
Six locations
for additional
limiting screws
Permanent
limiting screw
30º
90º
135º
Insert the two
limiting screws
to set the desired
swivel range.
Permanent
limiting screw
Metal bracket
Remove these
screws to release
the metal bracket.
Bottom of TSW-560/760/1060-TTK
