background image

Waterproof Wireless Handheld Remote 

Crestron 

WPR-48

 

 

LEFT PRESS 

VALUE 

 

BUTTON 

RIGHT PRESS 

VALUE 

[0] 1 

[1] 

[2] Set IR ID 

[3] Set RF ID 

[4] 3 

[5] 

[6] 

[7] 

[8] 5 

[9] 

[A] 

[B] 

[C] 7 

[D] 

[E] 

[F] 

To enter the ID number, (two hexadecimal numbers), press the corresponding 
buttons, such as [6] [B]. The page LEDs then go out indicating that the ID has been 
set. 

User-Printable Customized Button Labels 

Use the Crestron Engraver software package, Version 2.2 or later, available from the 
Downloads | Software Updates section of the Crestron website (

www.crestron.com

to design and print unique button labels. (Also requires Crestron Database, version 
16.3 or later.) 

The help file included with the software package provides detailed instructions for 
selecting the buttons and entering the legends 

To design the button labels for the WPR-48, open the Engraver software package 
and do the following: 

1.  When the “Choose Panel Type” window appears, click on the 

Create a new 

Engraver File

 button, select 

WPR-48

 from the drop-down list. Then, in the 

“Options” area, select white text on a black background or black text on a 
white background, and click 

OK

. The button layout screen appears as 

shown in the following illustration (shown here with populated fields; white 
text on a black background). 

10  

  Waterproof Wireless Handheld Remote: WPR-48 

Operations Guide – DOC. 6254A 

Summary of Contents for WPR-48





























Reviews: