background image

Crestron 

WPR-48 

Waterproof Wireless Handheld Remote

 

Physical Description 

The WPR-48 electronic hardware is housed in a slim, rubberized plastic, waterproof 
enclosure, with two clear windows for large customized labels that identify the 
intended button functions. (Refer to the illustration on the next page.)  
Electroluminescent backlighting enhances the labeling and makes it possible to read 
the button functions even in the dark. 

WARNING

:

  The WPR-48 Wireless Handheld Remote has been tested and found to 

be waterproof when submerged to a maximum depth of 1 meter, for a maximum 
duration of 30 minutes, per IEC 60529 IPX7 standards. Exceeding these limits may 
result in damage to the equipment, possible personal injury, and void the product 
warranty.

  

The unit is shipped with the lanyard foot installed. The lanyard foot puts the unit at a 
convenient angle when the unit is placed on a flat surface; the lanyard makes it easy 
to carry the unit around the home. A blank foot is supplied for those installations in 
which the unit is usually left in one location. 

Refer to “User-Printable Customized Button Labels” on page 10 for details about 
creating button labels. 

WPR-48 Waterproof Wireless Handheld Remote with Lanyard and Customized Button 
Labels, Mounted in Docking Station 

 

Operations Guide – DOC. 6254A 

Waterproof Wireless Handheld Remote: WPR-48  

  3 

Summary of Contents for WPR-48





























Reviews: