background image

 

24 

 

 

OPERATION 

 

 ARMING 

To arm the alarm and lock the doors, press the #1 Button on any remote.  You will hear a single siren chirp and the lights will 
flash once. The system will arm, the doors will lock (optional) and the starter (optional) will be disabled. The red in-dash LED 
in the vehicle will begin to flash.  After a short delay of 10-15 seconds to allow vehicle and electronics to stabilize the system 
will be completely armed. 

 
 

DISARMING 

To disarm the alarm and unlock the doors, press the #2 Button on any remote.  You will hear 2 siren chirps and the lights will 
flash  twice.    The  in-dash  LED  stops  flashing  dome  light  turns  on  (Optional).    If  the  alarm is  currently  tripped,  then  the  #2 
Button will have to be pressed two times.  The first press will only reset the pager (Beep) and the second press will disarm 
the system.   

 

ALARM TRIGGERING

 

If there is an intrusion into the vehicle, the alarm siren will sound and flash the lights for 30 sec..  This is known as a cycle.  
After the cycle, the system will automatically reset and continue to protect the vehicle.  If a door was left opened, then the unit 
will trigger up to 6 cycle, reset, and continue to protect the other un-tampered zones.

 

 

 

REMOTE PANIC PROTECTION 

To sound the alarm upon command (panic), press and hold the Button #4 on any transmitter for at least 2 seconds until the 
siren sounds and lights flash.  Repeat again to reset the panic mode.  Panic will sound for a maximum of 30 sec. 

 

SILENT ARM/DISARM 

Press the transmitter 

 

and

   

buttons at the same time will arm or disarm your security system, No chirp sound will be heard, 

arm / disarm confirmation will be through the vehicles parking lights only. 

 
 
 

SHOCK / IMPACT PROTECTION WITH PRE-WARNING 

Once the system is armed, if a low-level shock to the vehicle body is detected, the pre-warning sensor activates LED Remote 
and parking light flash three 3 times as a Warn-Away feature.  If a hard impact to the vehicle is detected the system will go 
into a full trigger cycle for 30 seconds.  Adjust the shock sensor as needed by turning the control knob clockwise or counter-
clockwise to increase or decrease the sensitivity.  Shock sensors will “settle in” over time and it may take a few tries over a  
few  weeks.  To  get  the  adjustment  correctly  for  your  vehicle,  we  recommend  a  moderate  adjustment  where  the  vehicle is 
protected but it is not constantly triggering from the slightest vibration creating a nuisance. 

 
 

DOOR OPEN WARNING 

If the system detects a faulty or open zone (Door left open), it will notify you by providing 3 warning chirps from the siren 5/60 
seconds  after  arming.    If  you  receive  this  warning,  check  to  see  if  a  door  is  ajar.    If  you  are  unable  to  do  so,  then  this 

Summary of Contents for CS-2205

































Reviews: