background image

SuperGap Evolution 2

Vacuum Pump

13485

 DE

S

 G

A

E

M

S

E

T

T

Ã

S

O

I

S

 

To develop innovative solutions to protect life and promote health.

       Cristófoli Equipamentos de Biossegurança Ltda., established at Rodovia BR-158, nº 127, 
Jardim Bandeirantes in Campo Mourão, Paraná, Brazil, manufactures biosafety equipment to 
assist the health care, having the following policy: "To develop innovative solutions for health 
care by using agile, robust, and objective processes to better serve its customers. To fulfill all the 
requirements of the applicable standards, promote the continuous improvement of its quality 
and  environmental  standards,  prevent  pollution,  reduce  its  environmental  impact,  and 
continuously train its staff, achieving, therefore, a sustainable and profitable maximization of its 
value." Rev. 2.

CRISTÓFOLI’S MISSION

CRISTÓFOLI QUALITY AND ENVIRONMENTAL POLICY

Cristófoli,  Brazilian  importing  company  and  manufacturer  of 
health  products  certified  by  ISO  13485  -  Health  Products  - 
Quality Management System -   Requirements for Regulatory 
Purposes  and  compliance  with  RDC  16/2013  -  *BPF  -  Boas 
Práticas de Fabricação - ANVISA requirements.

Summary of Contents for SuperGap Evolution 2

















Reviews: