Coolant Pump
This is the correct Pump to maintain proper
coolant circulation.
42500170
(for Cat. No. VE1P) 110V AC Coolant Pump
42500160
(for Cat. No. AU11) 220V AC Coolant Pump
Minimum order is one each.
Coolant Hose and Valve
Controls and directs coolant to the Diamond and
Polish Wheels.
42333006
12" Coolant Hose w/Fittings (no valve)
42333008
Valve only
Minimum order is one each.
Wheel Mounting Bolt Kit
These are the correct stainless steel bolts for se-
curing the Polish and Diamond Wheels. Set in-
cludes four flat washers, four lock washers and
four bolts each of five lengths: 1" (25 mm), 1-1/4"
(32 mm), 1-1/2" (38 mm), 1-3/4" (44 mm), and
2" (51 mm).
39528200
Kit of all 20 Bolts
Minimum order is one bolt kit.
Hex/Allen T-Wrench
Use the correct Hex/Allen T-Wrench to work with
the Wheel Bolts above.
46906580
T-Wrench
Minimum order is one each.
Conveyer Roller and Shoulder Screw
These are the rubber Rollers that support the
glass as it enters and exits the Edger.
16300160
Conveyor Roller
36988804
Roller Shoulder Screw
Minimum order is one each.
Platen Belt
The rubber Platen Belt that moves the glass
through the Edger. Replace yours if it is stretched,
cracking or contaminated.
43313220
Drive Belt
Minimum order is one each.
Wheel Position Dial Indicator
Dial Indicators allow precise positioning of Grind
and Polish Wheels. Record settings for quick
repositioning of Wheels during changeover.
49000510
Replacement Dial Indicator (1 only)
39700000
Dial Indicator Kit, (2)Complete*
39700001
Dial Indicator Kit, (2)Complete**
* for machines built BEFORE April 1, 2003 (see serial No. on machine)
** for machines built AFTER April 1, 2003 (see serial No. on machine)
Minimum order is one each.
Pressure Roller and Bushings
Pressure Rollers hold the glass against the platen
belt. Bearings can wear and must be replaced for
correct alignment. Three rollers, three upper and
three lower Bearings needed per Edger.
46300230
4" Pressure Roller
39663102
Lower Pressure Roller Bearings
39663101
Upper Pressure Roller Bearings
Minimum order is one each.
Brush Shields
Brush Shields keep water inside the Edger and
off of your work area. If yours are worn or
contaminated, replace them with these parts.
Two Main and two End Shields per Edger.
39223200
Main Brush Shield
39021400
End Brush Shield
Minimum order is one each.
Rubber Wiper
These small rubber “doors” keep water inside of
the Edger. Two needed for each Edger.
39021500
Rubber Wiper
Minimum order is one each.
Replacement Glass Rack Rail
Rails for the current model VE1P. They DO NOT
FIT older models without additional parts and
modifications. Each is cut to size shown.
39983001
120-3/4" Glass Rack Rail
39983002
49-7/8" Glass Rack Rail
39983003
46" Glass Rack Rail
Minimum order is one each.
End Cap for Rack Rail
These end caps fit on all the Glass Rack Rails
used on various models of the VE1P Edger.
46300079
Rack Rail End Cap
Minimum order is one each.
CAT. NO. DESCRIPTION
CAT. NO. DESCRIPTION
CAT. NO. DESCRIPTION
CAT. NO. DESCRIPTION
CAT. NO. DESCRIPTION
CAT. NO. DESCRIPTION
CAT. NO. DESCRIPTION
CAT. NO. DESCRIPTION
Bolts should be 1/4”
(6 mm) longer than the
total thickness of the
wheel(s) being used.
CAT. NO. DESCRIPTION
CAT. NO. DESCRIPTION
CAT. NO. DESCRIPTION
CAT. NO. DESCRIPTION
Owner’s Manual
VE-1P Vertical Edger
Factory Replacement Parts and Accessories for the VE-1P/AU11 Edger
Parts Page 34
