background image

NEXUS AM Deactivator 

 

 

 

 

 

Configuration 

v2.1 

Page 21 of 26 

7.5 

Notifications 

The NEXUS AM Deactivator can notify the user whether the deactivation  was successful 
or not. In the ‘Notifications screen’ the notifications for successful and failed deactivations 
can be configured. 

 

Figure 13: Notifications 

 

The successful, failed and tag too long in field notifications settings for buzzer and lights 
(located  in  the  housing  of  the  deactivator)  can  be  freely  configured  according  to  the 
wishes of the user. 

In  case  the  deactivator  is  configured  as  tag  detector  (see  section  xxx),  also  the  Tag 
detected notifications can be set. 

Notification  settings  can  be  saved  for  usage  in  other  stores.  Click  the 

Load  and  save 

notifications

 

button  and  select  the  option  ‘Save  notifications’  from  the  menu  and  the 

Save notifications dialog opens.  

A list with pre-defined notifications that have previously been saved appears. Select one 
from  the  list  to overwrite the  selected  pre-defined  notification,  or  enter  a  new  name  and 
description for the new notification. 

If  you  have  an  active  internet  connection,  you  can  also  tick  the  checkbox  in  front  of  the 
option 

‘Save  on  server’  to  store  this  new  pre-defined  notification  centrally,  so  it  is  also 

available for your colleagues. 

Click the Save button to store the notification. 

 

 

 

Summary of Contents for NEXUS AM



























Reviews: