background image

NEXUS AM Deactivator 

 

 

 

 

 

Terms and abbreviations 

v2.1 

Page 4 of 26 

Terms and abbreviations 

This chapter describes the terms and abbreviations used in this document. 

Term 

Abbreviation 

Explanation 

(Hard) Tag 

Tag 

Passive component, equipped with a lock 
to  allow  attachment  to  garments,  which 
can be detected by the receiver. 

(Paper) Label 

Label 

Passive  component,  usually  equipped 
with  glue  on  one  side  to  allow  attaching 
the  label  to  any  object,  which  can  be 
detected by the receiver.   

Antenna 

ANT 

The  mechanical  structure  (which  usually 
consists  of  a  frame,  wires  and  electronic 
PCB)  to  allow  proper  detection  of  tags 
and labels. 

Also referred to as: pedestal, barrier. 

Burst Frequency 

Fb 

The operating frequency of the TRX. 

Device Explorer 

Device Explorer 

Cross 

Point 

Device 

Explorer 

Software  tool  for  adjustment  of  Cross 
Point  devices  that  are  connected  to  the 
Cross Point Field Bus structure (RS-485). 

EAS 

EAS 

Electronic Article Surveillance 

Foiled Twisted Pair 

FTP 

The FTP cable is surrounded by an outer 
foil shield. 

I/O 

I/O 

Digital Input/Output  

Printed Circuit Board 

PCB 

The electronic board. 

Radio Frequency 

RF 

Electronic 

signals 

generated  by 

transmitter and detected by a receiver. 

Receiver 

RX 

Electronic  device  capable  of  receiving 
AM signals. 

Transceiver 

TRX 

Electronic  device  capable  of  transmitting 
and  receiving  AM  signals,  sharing  the 
same  electronic  circuitry  and  housing. 
Also referred to as mono-antenna. 

Unshielded Twisted Pair 

UTP 

Common network cable. 

 

 

 

 

Summary of Contents for NEXUS AM



























Reviews: