background image

INSTRUCTION MANUAL

1200-05 IF Processor, Filtered AGC Detection, 70 ±0.2 MHz 

    TABLE OF CONTENTS

PAGE

Warranty

2

1.0 General

3

1.1  Equipment Description

3

1.2  Technical Characteristics

4

2.0 Installation

5

2.1  Mechanical

5

2.2  Rear I/O’s, Control

6

2.3  Front Panel I/O’s, Indicators

6

2.4  Operation

7

1.3   Environmental Use Information

9

WARRANTY - The following warranty applies to all Cross Technologies, Inc. products.

All Cross Technologies, Inc. products are warranted against defective materials and 
workmanship for a period of one year after shipment to customer.  Cross Technologies, 
Inc.’s obligation under this warranty is limited to repairing or, at Cross Technologies, 
Inc.’s option, replacing parts, subassemblies, or entire assemblies.  Cross Technologies, 
Inc. shall not be liable for any special, indirect, or consequential damages.  This 
warranty does not cover parts or equipment which have been subject to misuse, 
negligence, or accident by the customer during use.  All shipping costs for warranty 
repairs will be prepaid by the customer.  There are not other warranties, express or 
implied, except as stated herein.

C

ROSS 

T

ECHNOLOGIES, INC.

6170 Shiloh Road

Alpharetta, Georgia 30005

(770) 886-8005

FAX (770) 886-7964

Toll Free 888-900-5588

WEB  www.crosstechnologies.com 

E-MAIL  info@crosstechnologies.com

1200-05 Manual, Rev. 0 

 

Page 2

    

                 10/14/10

Summary of Contents for 1200-05











Reviews: