Crosslinking DR 020 Operating Manual Download | Manualshive

Page: 12 / 14

background image

Page 12 of 14

11.2 Service mode 2

If the keys T1 and T2 are pressed at the same time during start-up, the device is switched to
service mode 2. This mode displays important data to simplify diagnostics.
The instrument-specific calibration factor (App.fact) which compensates for the hardware of
different devices can also be set in this mode. Do not change the instrument-specific calibration
factor! Adaptations regarding different dosimeter film batches can be made by modifying the
film-specific calibration factor (foil fact).

Flow chart / menu structure

«
...
10
11
12
13
14
»

Summary of Contents for DR 020















Reviews:

No comments

Related manuals for DR 020

Brand: Campbell Pages: 25

Brand: Larson Davis Pages: 2

Brand: G-Tek Pages: 27

Brand: VeEX Pages: 2

Brand: Callaway Pages: 11

Brand: i-SENS Pages: 50

Brand: Narvitech Pages: 2

Brand: Yamaha Pages: 72

Brand: Yamaha Pages: 5

Brand: Yamaha Pages: 16

Brand: Yamaha Pages: 8

Brand: Yamaha Pages: 7

Brand: Yamaha Pages: 60

GranTouch Digital Grand Piano

Brand: Yamaha Pages: 19

Brand: Yamaha Pages: 44

Brand: Yamaha Pages: 29

Brand: Yamaha Pages: 47

HF scientific AccUView LED

Brand: Watts Pages: 40

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands