background image

OWNER’S MANUAL

MODEL: PS-001 PRO STEAMER

REVISED JAN, 2006

*PLEASE RETAIN FOR FUTURE REFERENCE

CONGRATULATIONS!

You are the proud new owner of the finest commercial mobile

steamer available. CROWN VERITY Inc. Pro steamers are designed to last a
lifetime...or more! With proper care and maintenance, your steamer will provide
unparalleled performance and many years of outdoor cooking pleasure.

Please read this manual carefully to ensure safe operation and to maximize your
cooking enjoyment. It is your responsibility to see that your steamer is properly
assembled, installed, and cared for. Failure to follow instructions in this manual could
result in serious bodily harm and/or property damage.

WARNING:  Improper installation, adjustment, alteration, service or

maintenance can cause property damage, injury or death.  Read the

installation, operating and maintenance instructions thoroughly before

installing or servicing this equipment.

CROWN VERITY INC., 37 ADAMS BLVD., BRANTFORD, ON. CAN. N3S 7V8

TEL: (519) 751-1800

FAX: (519) 751-1802

www.crownverity.com

Email: info@crownverity.com

Certified for use in Canada and the
United States of America.

Certified to / a.: CSA 1.8 2004, CSA
1.18 2004

Conforms to / Conforme a: ANSI std
Z21.89 2004 / ANSI std Z83.112004

 

 

 

 

 

 

Summary of Contents for PS-001
















Reviews: