background image

13

PARTS AND COMPONENTS 

DESCRIPTION

STEAMER BODY ASSY.

STEAMER LID (INCLUDED WITH TANK)

UNDER SHELF

STEAMER BASKET

HOSE & REG ASSY.

OPERATOR FRONT LEFT LEG

OPERATOR FRONT RIGHT LEG

OPERATOR BACK LEFT LEG

OPERATOR BACK RIGHT LEG

BURNER W/ ORIFICE

14” WHEELS

5” CASTER

STAINLESS STEEL AXLE

BRONZE NAME PLATE

HANDLE 9”

LIGHTING INSTRUCTIONS DECAL

RATING PLATE DECAL

1/4”-20x5/8” HEX BOLT

1/4” FENDER WASHER 1.25” O.D.

5/16” INT. TOOTH LOCK WASHER

5/16”-18 FULL HEX NUT

5/16”-18x5/8” RSLMS

1/2” FLAT WASHER 

1/8”x1 COTTER PIN

1/2”-13x5/8” HEX BOLT ZINC

CAUTION HOT STEAM DECAL KIT

CASTER BRACKET

CASTER MOUNT

3/4” BALL VALVE

3/8” FEM FLR x 1/4” MPT 

1/4” x 3/8” ELBOW

3/8” FPT x 3/8” FLR

3/8” x 8” BRASS NIPPLE

PART #

9010

9011

8071

9020

2300

2217

2213

2218

2212

9060

2141

2216

2215

2003

2219

2205-S

2206-S

2026

2019

2013

2014

2142

2146

2148

2031

9040

2220

2211

9050

9051

9052

9053

9054

QTY

1

1

1

1

1

1

1

1

1

1

2

2

1

1

2

1

1

4

4

22

22

22

5

2

2

4

2

2

1

1

1

1

1

TO ORDER PARTS PLEASE CONTACT

CROWN VERITY INC., 37 ADAMS BLVD., BRANTFORD, ON. CAN. N3S 7V8

TEL: (519) 751-1800 FAX: (519) 751-1802  www.crownverity.com  Email: info@crownverity.com

Due to a

continuous

program of

product

improvement

Crown Verity

Inc. reserves

the right to

make

changes in

design.

Summary of Contents for PS-001
















Reviews: