background image

2

INSTALLATION

THE INSTALLATION OF THIS APPLIANCE MUST BE IN ACCORDANCE WITH:

1) All applicable local codes, or in the absence of local codes;

2) i)  Canada: must conform to current National Standard CAN/CGA B149.1&.2

natural gas/propane installation code.

ii) U.S.A.: must conform to national Fuel Gas Code, ANSI Z223.1, 1988 or latest

edition.

WARNING!

DO NOT

operate this appliance under overhead, combustible construction. This

appliance shall be used only in a well-ventilated space and shall not be used in a
building, garage, or any other enclosed area.

MINIMUM CLEARANCE TO COMBUSTIBLE MATERIALS:

18 inches from all sides

• Always keep the surrounding area clear of all combustible materials, gasoline, or other

flammable liquids

• This appliance is suitable for use on combustible floors.

• Always level your Pro Steamer front to back & side to side. . 

• Use your Pro Steamer OUTDOORS in a well-ventilated space, 10 ft. from dwellings or

outbuildings.

• Casters must be locked when appliance is in operation.

ALWAYS PLACE THE PRO STEAMER ON A FIRM, LEVEL SURFACE
WHEN OPERATING

CROWN VERITY INC., 37 ADAMS BLVD., BRANTFORD, ON. CAN. N3S 7V8

TEL: (519) 751-1800

FAX: (519) 751-1802

www.crownverity.com

Email: info@crownverity.com

Certified for use in Canada and the United States of America.
Certified to / a.: CSA 1.8 2004, CSA 1.18 2004
Conforms to / Conforme a: ANSI std Z21.89 2004 / ANSI std
Z83.112004

This outdoor cooking gas appliance is not for installation in or on recreational vehicles
and/ or boats.

Summary of Contents for PS-001
















Reviews: