background image

13 

 

3-CHANNEL WIRING

 

 
The amplifier inputs are white cables. Each cable is marked with a numbered band at the end of the 
cable. 
 
1. Refer to 

Figure 9

 for the following connections: 

 
Connect CH 1 signal (left) to white input cable 1. 
Connect CH2 signal  (right) to white input cable 2. 
Connect CH3 signal  (Subwoofer) to white input cable 5. 
 
NOTE: White input cables 2 and 4 are not used. To avoid accidental shorting of these cables to the 
chassis, and to reduce noise, use a wire nut to connect the “hot lead” and shield in each cable. 
 
 
2. Set the amplifier switch to 3 CH as in 

Figure 10

. This provides the following output powers: 

 
CH1: 100 W at 8 ohms 
CH2: 100 W at 8 ohms 
CH3: 100 W at 8 ohms 
 
(These are minimum recommend loads.) 
 
3. Refer to 

Figure 9

. Connect the speakers as follows. Route the CMA-1 colored output cables 

separate from its white input cables to prevent oscillations. Using crimp terminals, connect the 
CMA-1 colored cables to the speaker terminals, taking care to observe the cables colors and 
polarities noted below: 
 
Blk/Wht: 

CH 1 + 

Left Speaker 

Wht/Red: 

CH 2 + 

 

Red/Wht: 

CH 2 + 

Right Speaker  

Grn/Yel: 

CH 2 + 

 

 
Blu/Red: CH 

3+  Subwoofer 

Yel/Red: 

CH 3 - 

 

 
NOTE: The Back, White, Red and Green cables are not used. To avoid accidental shorting of these 
cables, clip exposed ends back to the insulation, and cover with electrical tape. 
 

Summary of Contents for CMA-1
















Reviews: