background image

INSTALLATION AND OPERATION MANUAL, GAS SKILLETS, MODELS GTS-30, GTS-40

PART NUMBER 10093R2

    2

  

   2003-07-08

IMPORTANT NOTES FOR INSTALLATION AND OPERATION

It is recommended that this manual be read thoroughly and that all instructions be followed
carefully. This manual should be retained for future reference.

This is the safety alert symbol.  It is used to alert you to potential
personal injury hazards.  Obey all safety messages that follow this
symbol to avoid possible injury or death.

FOR YOUR SAFETY:  Do not store or use gasoline or other flammable
vapors or liquids in the vicinity of this or any other appliance.

PURCHASER:  Instructions to be followed in the event that the operator of this
appliance smells gas must be posted in a prominent location.  This information
shall be obtained by consulting the local gas supplier.

WARNING:  In the event you smell gas, shut down equipment at the
main shut off valve and contact the local gas company or gas
supplier for service.

Do not attempt to operate this unit in the event of a power failure.

Keep the appliance area free and clear from combustibles.

Do not obstruct the flow of combustion and ventilation air.

Adequate clearances must be maintained for servicing and proper operation.

    

WARNING:  Improper installation, operation, adjustment, alteration,
service or maintenance can cause property damage, injury or death.  
Read the installation, operating and maintenance instructions
thoroughly before installing, operating or servicing this equipment.

NOTICE:  Contact the factory, the factory representative or local service
company to perform maintenance and repairs.

Summary of Contents for GTS-30













Reviews: