background image

 

3. Depress the 

FEED

 key until the paper begins to 

advance through the printer. 

 

4. If the paper refuses to feed through the printer, make   

                 certain the end of the tape is square and that  
                 it is routed properly. 

 

                                          

FOR RECEIPT ONLY 

...

 

 

5.

 

Pass paper through the receipt 

                  window of printer cover. Replace  
                  over printer compartment. 

 

                                           

FOR JOURNAL ONLY 

...

 

 

6.

 

Route paper over top of paper  

                  guide and insert in the 
                  slot of the take-up spool. 

 

7.

 

Press the 

FEED

 key to wind  

                  paper securely on the spool. 

 

    8. Replace printer cover. 

 

 

REPLACING THE INK ROLLER

 

 

Ink roller are disposable, and should not be re-inked. Re-inking 
can cause damage to the printer that is not simply replace the 
ink roller in the following manner : 

 

1. Remove the old roller by lifting  
    straight up on the lever located  
    on the left side. 

 

2. Place the new roller in position  
    (handle to the left) and snap it  
    into place by pressing it straight  
    down. 

 
 
 

1

2

3

4

5

6

1

2

3

4

5

6

1

2

3

4

5

6

Lever

Summary of Contents for ER-150
































Reviews: