Place terminal in a secure
position so that it won’t
accidentally contact the
negative battery post
Properly route power,
speaker and RCA cables
through the vehicle.
Choose a mounting location
that will provide adequate air
ventilation. Mount the amplifier to
a secure surface. Do not mount
the amplifier upside down.
Using spade terminals, connect the
+12V to the power cable from the
battery, the REM to the source unit
turn-on wire and the GND to the
chassis ground..
Strip each cable back approx 1/2”,
connect the +12V to the power
cable from the battery, the REM to
the source unit turn-on wire and the
GND to the chassis ground..
Bare metal
Connect the RCA cables to
the INPUT connectors. The
OUTPUT can be used to
provide input for a second
amplifier.
cable
Conn
Connect
ect the
ect
Conn
battery te
positive
positive
The
power
power
power
power cabl
with
within
wit
within
in 18 inches
terminal.
Re-connect the negative
battery terminal making sure it
is securely tightened.
Using spade terminals,connect
the speaker cables
the s
to
peaker c
output connectors. Follow the
best fits your
diagram below that
speaker configuration.
The chassis ground connection
is critical to the performance
of the amplifier. Choose a
location that is close to the
amplifier. Completely scrape
away the paint and use a nut
and bolt if possible.
DO NOT USE AN EXISTING
FACTORY BOLT!
Disconnect
negative battery
terminal
Run Cables
Mount Amplifier
Power
Connections
Smaller amps
Signal Input
Low Level RCA
Power
Connections
Larger amps
Signal Input
High Level
Battery
Positive
Connection
Re-connect
Negative Battery
Terminal
Speaker
Connections
Chassis Ground
e prepar
Be
B
ed
Be prepared to disarm
s alarm and
o enter your radio / sour
o en
t enter
tto
Stereo
Power / Ground
cable size
It is critical to use the proper
power and ground cable. Select
the size listed here for your
amplifier model. Always use high
quality copper cable.
Cable size recommendations for
multi amp systems are available
on our website.
Installation
Before you start
Monoblock
single woofer
Monoblock
multiple
multiple
Bridged
CAUTION
Many new and factory radios require a reset code when
disconnected from battery power. This is an anti-theft
feature. Before unplugging power, you must determine if
your radio/source unit requires a reset code. Check the
operation manual for your vehicle or contact the dealer.
1
2
3
5
a
5
b
6
7
10
11
9
4
Turn the LEVEL control completely
counter-clockwise to minimum.
The HI INPUT is for use with
source units that do not offer
RCA outputs. Use the supplied
harness to connect to the
source unit’s speaker output.
8
Level Control
6V
0.2V
INPUT
LEVEL
SPEAKER
LEFT
RIGHT
BRIDGED
OUTPUT
SPEAKER
OUTPUT
SPEAKER
OUTPUT
SPEAKER
LEFT
RIGHT
BRIDGED
OUTPUT
Right + (gray)
4CH REAR
Ch3 Right + (orange)
Ch3 Right - (pink)
Chassis Ground (black)
Ch4 Left + (blue)
Ch4 Left - (yellow)
Connect to factory speater wire directly
Left - (green)
Left + (white)
Right - (brown)
Chassis ground (black)
4ga
8ga
Cable Size
Fuse Size
Model
1-30A
1-30A
2-30A
2-30A
2-35A
2-40A
1-30A
2-15A
2-25A
2-40A
2-25A
2-30A
2-40A
PD800.2
PD1100.2
PD1500.2
PD2000.2
PD3000.2
PD4000.2
PD1000.4
PD1400.4
PD2000.4
PD4000.4
PD1500.1
PD2100.1
PD3000.1D
