Crux Sightline PCM-3 Manual Download

Page: 3 / 10

CONNECTING THE INTERFACE

Follow these steps to properly install interface module.

Step 1

- Remove the factory radio to gain access to the factory 40-Pin connector.

Remove the factory 40-Pin connector.

Your radio face may di er.

Step 2

- Prior to connecting the interface, we recommend taping the 4 wires necessary to power the module.

Connect the 4 loose wires from the harness to the 4 designated wires on the factory 40-Pin connector.

Factory Connector Pin Assignments

COLOR

DESCRIPTION

TAP PIN

RED =

12V CONSTANT

BLACK =

GROUND

ORANGE/BROWN =

CAN-LOW

ORANGE/PURPLE

CAN-HIGH

Crux holds no liability for the vehicle wiring

color codes and pin

ration.

As there may be changes by the vehicle

manufacturer that we may not be aware of.

Installer must verify this information prior

to being installed.

FUSE

12v

GROUND

CAN-LOW

CAN-HIGH

Rear-View Integration Interface for

PORSCHE Vehicles with PCM-3 or PCM-3.1 Systems

PCM-3

INTERFACING SOLUTIONS

Sightline

REAR-VIEW INTEGRATION

Crux Interfacing Solutions • 6860 Canby

Ave., Suite 1

16, Reseda, C

A 91335

phone: (818) 609-9299 • fax: (818) 996-8188 • www

.cruxinterfacing.com

3 of 10

rev.051718

Summary of Contents for Sightline PCM-3











Search results

Summary of Contents for Sightline PCM-3

Reviews:

Related manuals for Sightline PCM-3

Brands by name

Popular brands

Crux Sightline PCM-3, Manual

Search results

Summary of Contents for Sightline PCM-3

Reviews:

Related manuals for Sightline PCM-3

Brands by name

Popular brands