background image

Burner regulation 
When the burner is in operation, hold the handset as described above 
to unlock the keypad and then press and release the + and – buttons to 
regulate the flame of the burner. Pressing and releasing the button will 
move the burner one step at a time. Pressing the button continuously 
will move the burner rate to the maximum full when pr or 
minimum burner power if pressing  -. 

!

Stopping the burner 
Pick up and hold the handset as described above to unlock the keypad. 
Press and then release the power button once. The handset will beep 
and the burner will stop. 

!

!

Auxiliary button 
If your fire is fitted with an Auxiliary feature (lights , fans etc) this 
button will operate those devices when pressed. Hold to unlock as 
usual, then Press once and release to start that auxiliary device ,press 
again and release to stop. 

!

!

!

Installer note: 
To reset the handset to factory conditions (to enable the handset to 
be paired with another fire for example), hold handset to unlock, press 
and hold for at least 10 second the SET button. The green and red 
lights will start to flash. They will flash for 1 minute and during this 
minute if you want to reset the handset, open the battery box and 
remove a battery for a few seconds. Replace the battery and cover, 
the handset will now be reset and ready to pair as a new handset to 
another (or the same) device as shown above in pairing section. 

!

!

!

Paging the handset 

If you have misplaced the handset you can page it by pressing the + button 
only on the fire control for around 5 seconds. The handset will flash and 
make a noise to help you to locate it. Once you pick up the TESC it knows you 
hold it and so the sound stops. The flashing and sound will last for 60 seconds 
each time the handset is paged as described. If not found in 60 seconds, 
page again and so on. NOTE: PRESS “+” Button ONLY , NOT “+” and “-‘ 
Together as you will accidentally break the handset pairing and have to reset 
handset to factory state and pair again ( see other parts of the booklet if 
this happens). 

!

!

 

11

Summary of Contents for TESC 001














Reviews: