crystal fires TESC 001 Addendum Instructions Download | Manualshive

Page: 13 / 13

background image

Burner regulation
When the burner is in operation, press and release the + and – buttons
to regulate the flame of the burner. Pressing and releasing the button
will move the burner one step at a time. Pressing the button
continuously will move the burner rate to the maximum full when
pr or minimum burner power if pressing -.

!

Stopping the burner

!

Press and then release the power button once. The burner will stop and
the red indicator light will illuminate momentarily to show the fire is
turning off.

!

!

!

!

!

!

!

!

!

!

INJECTOR : 500

!

SPARE PARTS : TESC REMOTE HANDSET TESC 001
: ODS PILOT TESC 002

!

APPLIANCE

HIGH RATE

LOW RATE

SUPER HEATRAVE

!

6.5Kw

4.1kW

SLIMLINE

6.5Kw

4.1kW

DIAMOND

6.5Kw

4.1kW

JEWEL

6.9Kw

4.1kW

JEWEL HIW

6.9Kw

4.1kW

CF2 MONTANNA

5.2Kw

2.6Kw

CF1

5.5Kw

2.9Kw

GEM

6.9Kw

4.1kW

SAPHIRE

6.2Kw

3.8 kW

!

13

«
...
11
12
13

Summary of Contents for TESC 001














Reviews:

No comments

Related manuals for TESC 001

Max Charge MC-624

Brand: Balmar Pages: 8

MAX CHARGE MC-614

Brand: Balmar Pages: 20

Brand: Federal Signal Corporation Pages: 79

Brand: Federal Signal Corporation Pages: 32

Brand: National Instruments Pages: 29

Brand: vacuubrand Pages: 12

Brand: Vacon Pages: 47

Brand: Vacon Pages: 40

Brand: RADEMACHER Pages: 68

Brand: PESA Pages: 30

Brand: Warner Electric Pages: 4

S3500 Series Uplink Module

Brand: Aruba Pages: 8

Brand: Lutron Electronics Pages: 2

Brand: PURSUIT Pages: 24

Brand: National Instruments Pages: 22

Brand: L&L Pages: 16

Brand: Hahnel Pages: 36

Brand: maxon motor Pages: 44

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands