background image

 

Parts Listing

The following parts list describes all of the parts illustrated on the 
exploded diagram on the following page.  Please note, most of 
these parts are already pre-assembled on your unit.

#

Description

#

Description

01

Main Frame

24

Round End Cap (25 mm)

02

Bottom Frame

25

Front Roller

03

Front Stabilizer

26

Rectangular Cap (53x23 mm)

04

Rear Stabilizer

27

Bottom Frame Sleeve

05

Front Post

28

Spring Loaded Knob (M16x25 mm)

06

Cushion Frame

29

Knob Bolt (M8x20 mm)

07

Rear Handle Bar

30

Knob 

08

Backrest Cushion

31

Carriage Bolt (M8x60 mm)

09

Seat Cushion

32

Bolt (M8x45 mm)

10

Monitor

33

Bolt (M8x20 mm)

11

Crank

34

Bolt (M8x15 mm)

12L

Left Pedal

35

Hex Bolt (M6x50 mm)

12R Right Pedal

36

Screw (M5x45 mm)

13

Water Bottle Holder

37

Screw (M5x10 mm)

14

Foam Grip for Rear Handle Bar

38

Screw (ST4x15 mm)

15

Foam Grip for Front Handle Bar

39

Screw (ST4x20 mm)

16

Tension Controller

40

Nut (M8)

17

Tension Controller Cable

41

Nylon Nut (M8)

18

Monitor Wire (Lower)

42

Nylon Nut (M6)

19

Monitor Wire (Middle)

43

Arc Washer (M8)

20

Monitor Wire (Upper)

44

Arc Washer (M5)

21

Hand Pulse Sensor

45

Washer (M8)

22

End Cap for Front Stabilizer

46

Washer (M6)

23

End Cap for Rear Stabilizer

47

Spring Washer (M8)

Page 3

SJ-3560

Summary of Contents for SJ-3560




















Reviews: