background image

MINI TRACKED DUMPER

5

GB

on the unit. Transporting or performing 
maintenance or service on a machine with its 
switch on invites accidents.

I f   t h e   m a c h i n e   s h o u l d   s t a r t   t o   v i b r a t e 
abnormally, stop the engine (motor) and 
check immediately for the cause. Vibration is 
generally a warning sign of trouble.

Engine Safety

This machine is equipped with an internal 
combustion engine. Do not use on, or near, 
forest-covered or brush-covered land unless 
the exhaust system is equipped with a spark 
arrester meeting applicable local, state, or 
federal laws.

In the state of California, a spark arrester is 
required by law. Other states have similar laws. 
A spark arrester, if used, must be maintained 
in effective working order by the operator.

Never start or run the engine inside a closed 
area. The exhaust fumes are dangerous, 
containing carbon monoxide, an odorless and 
deadly gas. Operate this unit only in a well-
ventilated outdoor area.

Do not tamper with the engine in an effort to 
get it to run at higher speeds. The maximum 
engine speed is preset by the manufacturer 
and is within safety limits. See engine manual.

Keep a Class B fire extinguisher on hand 
when operating this machine in dry areas as a 
precautionary measure.

Fuel Safety

Fuel is highly flammable, and its vapors can 
explode if ignited. Take precautions when 
using to reduce the chance of serious personal 
injury.

When refilling or draining the fuel tank, use 
an approved fuel storage container while in 
a clean, well-ventilated outdoor area. While 
adding fuel or operating the unit, do not 
smoke, and stay away from sparks, open 
flames, or other sources of ignition near the 
area of operation. Never fill the fuel tank 
indoors.

To avoid sparking or arcing, keep grounded 
conductive objects – such as tools – away 
from exposed, live electrical parts and 
connections. These events could ignite fumes 
or vapors. 

Always stop the engine and allow it to cool 
before filling the fuel tank. Never remove 
the cap of the fuel tank or add fuel while the 
engine is running or when the engine is hot. 
Do not operate the machine with known leaks 
in the fuel system.

Loosen the fuel tank cap slowly to relieve any 
pressure in the tank. 

Never overfill the fuel tank. Because engine 
heat can cause fuel to expand, never fill the 
tank to more than 1/2” below the bottom of 
the filler neck. This will provide space for fuel 
expansion.

Replace all fuel tank and container caps 
securely and wipe up spilled fuel. Never 
operate the unit without the fuel cap securely 
in place.

Avoid creating a source of ignition for spilled 
fuel. If fuel is spilled, do not attempt to start 
the engine. Instead, move the machine away 
from the area of spillage and avoid creating 
any source of ignition until fuel vapors have 
dissipated.

When fuel is spilled on yourself or your 
clothes, wash your skin and change clothes 
immediately.

Store fuel in containers specifically designed 
and approved for fuel storage.

Store fuel in a cool, well-ventilated area, safely 
away from sparks, open flames, or other 
sources of ignition.

Never store fuel – or a machine with fuel in 
the tank – inside a building where fumes may 
reach a spark, open flame, or any other source 
of ignition (such as a water heater, furnace, or 
clothes dryer). Allow the engine to cool before 
storing in any enclosure.

Summary of Contents for D30MB






























Reviews: