-19-
on the remote control, the illuminated operation
indicator
2
indicates that a signal was sent out.
Switching the rotational laser on/off with the
remote control is not possible.
Operating Modes
Function of buttons that are both on the
rotational laser level as well as on the remote
control do not differ. With exception of the
hibernation mode, no additional functions of the
rotational laser level can be controlled with the
remote control. Example: Pressing the rotation
operation button switches the rotational laser
level from line operation to rotation operation.
This happens no matter if you press the rotation
operation button on the rotational laser level
or on the remote control. When the rotational
laser level does not have different rotational
speeds, then the rotational speed can also not
be changed with the remote control.
The ADS function cannot be controlled with
the remote control. For detailed information of
the rotational laser functions, see the operating
instructions of the rotational laser.
Hibernation Mode
The rotational laser level can be switched to
hibernation mode for 2 hours (max.). For this,
press the hibernation mode button
1
on the
remote control. Rotation laser level is switched
off, and the set operating mode is saved.
hibernation mode can only be started with the
remote control.
Press any button on the remote control to restart
the rotational laser level in the saved operating
mode.
Rotation, Line and Point Operation
By pressing the rotation operation button
9
,
you can switch from line to rotation operation
or decrease the rotational speed in steps down
to zero (point operation). By pressing the line
operation button
3
, you can switch from rotation
to line operation or increase the aperture angle
in steps.
Rotating the Laser Point/Laser Line in the
Rotational Plane
The laser point or the laser line can be rotated in
steps by 360° within the rotational plane. Press
button
5
to rotate in clockwise direction, and
button
7
to rotate in counter clockwise direction
(See Fig. G).
Pressing and holding the buttons increases
the speed of the rotation head in the desired
direction.
Rotating is (independent of the
position of the rotational laser level) also
possible in single-axis slope operation (See Fig.
G).
Single-axis Slope Operation/Aligning the
Rotational Plane in the Vertical Position
Depending on the position of the rotational
laser level, you can rotate the rotational plane
around the X or Y-axis by pressing upper
direction button
11
, lower direction button
6
,
right direction button
4
and left direction button
8
. For this, press the button for single-axis
slope operation
10
first. When the rotational
laser level is in the horizontal position, you can
rotate the rotational plane around the Y-axis
with the upper direction button
11
and lower
direction button
6
. When the rotational laser
level is in the vertical position, you can rotate
the rotational plane around the X-axis with right
direction button
4
and left direction button
8
(See Fig. G).
Maintenance and Service
Maintenance and Cleaning
Keep the remote control clean at all times.
Do not immerse the remote control into water or
other fluids.
Wipe off debris using a moist and soft cloth. Do
not use any cleaning agents or solvents.
If the remote control should fail despite the care
taken in manufacture and testing, repair should
be carried out by an authorised customer
services agent for Bosch power tools. Do not
open the remote control yourself.
Summary of Contents for rl25h
