-29-
Always use the center of the laser point for
marking. The size of the laser point changes
with the distance.
Working with the Laser Detector
(Accessory)
Under unfavourable light conditions (bright
environment, direct sunlight) and for larger
distances, use the laser detector for improved
finding of the laser beam
21
.
RL25HV: When working with the laser detector,
select rotational operation with the highest
rotational speed. Before working with the laser
detector, read and observe the laser detector
operating instructions.
Working with the Remote Control
(Accessory)
While pressing the operator buttons, the
measuring tool can be brought out of alignment
so that the rotation is briefly stopped. This effect
is avoided when using the remote control
24.
The receiption lenses 1 for the remote control
are located on four sides next to the rotation
head. Before working with the remote control,
read and observe the remote control operating
instructions.
Working with the Tripod (Accessory)
The measuring tool is equipped with a 5/8”
tripod mount for horizontal operation on a
tripod. Place the measuring tool via the tripod
mount
18
onto the 5/8" male thread of the tripod
and screw the locking screw of the tripod tight.
On a tripod
23
with a measuring scale on the
elevator column, the height difference can be
adjusted directly.
Working with Wall Mount/Alignment Unit
(Accessory) (RL25HV)
You can also mount the measuring tool to the
wall mount with alignment unit
26
. For this,
screw the 5/8” screw of the wall mount into the
tripod mount
18
of the measuring tool.
Mounting to a wall: Mounting to a wall is
recommended, e.g., for work above the
elevation height of tripods or for work on
unstable surfaces and without tripod. For this,
fasten the wall mount
26
, with the measuring
tool mounted, as vertical as possible to a wall.
Mounting on a tripod: The wall mount
26
can also be screwed onto a tripod with the
tripod mount on the back side. This method
of fastening is especially recommended for
work where the rotational plane is to be aligned
with a reference line. With the alignment unit,
the mounted measuring tool can be moved
vertically (when mounted to the wall) or
horizontally (when mounted to a tripod) within a
range of approx. 15 cm.
Working with the laser target accessory
(see figure A)
With the laser target plate
28
, the laser mark
can be projected on the ground/floor or against
a wall. With the magnetic holder, the laser
target plate can also be fastened to ceiling
constructions. With the zero field and the scale,
the offset or drop to the required height can be
measured and projected at another location.
This eliminates the necessity of precisely
adjusting the measuring tool to the height to
be projected. The laser target plate
28
has a
reflecting coating which improves the visibility
of the laser beam from a larger distance or in
case of strong sun rays. The luminosity can be
recognized only if you look to the laser target
plate in parallel to the laser beam.
Working with the Measuring Rod
(Accessory) (see figure F)
For checking irregularities or projecting
gradients, it is recommended to use
the measuring rod
22
together with the
laser detector.
Working Advice
Summary of Contents for rl25h
