background image

16

Note: 

When collecting waveform data from the BNC jack on the signal 

conditioner using a portable data collector that supplies constant current power, 

it is recommended that the data collector is configured so that power to the 

sensor is turned off . Although the BNC connector circuitry offers short circuit 

protection and can safely sink the current, long-term degradation may occur due 

to increased power dissipation depending on the magnitude of the IEPE current . 

There is no need for the data collector sensor power to be turned on for the data 

collection to be made, and it is the safest way to make measurements if possible .

Troubleshooting

Signal Conditioner Configuration 

Refer to the 

SC310

 and 

SC320

 Series Signal Conditioner Product Manuals 

for configuration specifications and procedure for SC310 and SC320 signal 

conditioners . 
Once all wires are connected, apply power to begin operating the Signal 

Conditioner(s) . Make sure the status light is indicating normal mode on each 

SC300 . 

Operating Procedure

To operate the Signal Conditioners inside the enclosure, make sure that all wires 

are properly connected, and then apply power . 

Caution:

 Make sure that power input does not exceed specified limits or damage 

to the system may result . See Table 1 .

Calibration

The signal conditioner is calibrated internally during startup . The digital calibration 

eliminates the need for any adjustments to the Analog Output .

Indicators

The LED on the front of the signal conditioner will indicate the status of the signal 

conditioner .

State 1

 - Normal Operation

• 

LED is solid green

State 2

 - Input Short Detected

• 

LED is rapidly flashing red

Summary of Contents for SCE100 Series




















Reviews: