background image

3

Introduction

This document contains information on the operation, installation and 

maintenance of the SCE Series signal conditioner enclosure . This manual is an 

overview of the system and references the specific component manuals . User 

manuals are provided with the system for all configurable internal components .

Product Overview 

The SCE Series signal conditioner enclosure is a turnkey solution coming fully 

populated with signal conditioners, terminal blocks for sensor terminations, 

and optional power supply . The signal conditioners are already pre-configured 

based on the customer’s specific requirements . Terminal blocks are provided 

for your sensor wiring terminations . These terminal blocks are pre-wired to 

the signal conditioners and outputs from the signal conditioners are wired to 

terminal blocks for integration into PLC/DCS systems . Each signal conditioner 

utilizes screw terminals for the various input/output options such as, ±20 to 32 

V

dc

 power input, ± signal output (1-2 configurable vibration outputs [0mA-20mA, 

4mA-20mA, 0-5 V

dc

, 0-10 V

dc

] and a temperature output in 0 .1-1 .7 V

dc

) and  

± sensor input (vibration, displacement and temperature inputs) . There is also a 

green indicator light (Transducer Signal OK) which illuminates when the sensor is 

properly connected to the transmitter and working correctly . The power supply 

accepts input voltage of 100-240 V

ac

, 0 .68A and 50-60 Hz; and provides 24 V

dc

 

to the signal conditioners and sensors . The power supply terminals include AC 

Input Terminals (L) and (N), as well as Ground . DC Output Terminals are utilized in 

providing power to the vibration transmitters . The output voltage of the power 

supply is 21 .6 – 26 .4 V

dc

 .

Refer to the 

SC310 Series Signal Conditioner Product Manual

 for specific 

electrical, performance, and calibration instructions .

Summary of Contents for SCE400 Series





















Reviews: