CTI GG-R Installation And Operation Manual Download

Page: 3 / 12

GG-R

Table of Contents

For technical support, contact:

Calibration Technologies

920 N Trade Winds Pkwy

Columbia, MO 65201

866-394-5861

Sales@ctiengineering.com

www.ctiengineering.com

General description . . . . . . . . . . . . . . . . . . . . . 4

Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4

Locating the sensor

. . . . . . . . . . . . . . . . . . . 4

Installation guidelines

. . . . . . . . . . . . . . . . . 5

Wiring

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6

Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7

Start-up

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7

Calibration

. . . . . . . . . . . . . . . . . . . . . . . . . . . 7

Zero-filter mode

. . . . . . . . . . . . . . . . . . . . . . 9

Maintenance . . . . . . . . . . . . . . . . . . . . . . . . . . . 9

Specifications

. . . . . . . . . . . . . . . . . . . . . . . . . . 10

Warranty . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11

Summary of Contents for GG-R













Search results

Summary of Contents for GG-R

Reviews:

Related manuals for GG-R

Brands by name

Popular brands

CTI GG-R, Installation And Operation Manual

Search results

Summary of Contents for GG-R

Reviews:

Related manuals for GG-R

Brands by name

Popular brands