CTS SWH-2109FX User Manual Download

Page: 6 / 12

第

頁，共

頁

SWH-2109F

V1.1

standards

Supports N-Way protocol for 10Base-T and/or 100Base-TX connections Full/
Half duplex mode operation

Small size

Store-and-forward switching mechanism

Automatic filtering of fragmented and CRC error packets

Extensive LED indicators for network diagnostics

External power adapter

State Monitor - Model/Media/Link/Speed/Duplex/Activity

Enhanced Port Monitor – Port Traffic Counter

S/W Port Configuration - Support Auto/Speed/Duplex/Auto

MDIX/MDIX

Support SNMP management

Support Telnet management

Support console management

IP Configuration

DHCP

IP Security

Time server Configuration

User Authentication

Trap Configuration

FTP/TFTP firmware upgrade

Support 802.1Q Tagged VLAN

Port rate limiting included Broadcast storm

3 options but only one enable(port based Priority and 802.1P Priority supported and
TOS priority supported)

QOS support with four traffic classes

2.3

The Front Panel

The front panel of the switching hub is shown below.

Summary of Contents for SWH-2109FX













Search results

Summary of Contents for SWH-2109FX

Reviews:

Related manuals for SWH-2109FX

Brands by name

Popular brands

CTS SWH-2109FX, User Manual

Search results

Summary of Contents for SWH-2109FX

Reviews:

Related manuals for SWH-2109FX

Brands by name

Popular brands