background image

 9 

頁,共

 12 

 SWH-2109F 

V1.1 

 
 

 

NOTE: 

The default primary is Port F2 and Secondary is Port F1. 

 

2.4 The Rear Panel 

The rear panel of the hub is shown below 

 

2.4.1 Power Connecting 

Plug the circle end of the power adapter firmly into the rear panel of the switching 

hub, and the other end into an electric service outlet then the system is ready. 

 

2.4.2

 

DIP Switch 

The DIP switch reserved all of functions. 

 

2.4.3

 

Fiber Port 

The F1 and F2 are Fiber Optic link ports. 

 

2.4.4

 

Diag button 

Reserves 

   

3.    Installing and Using 9 Port NWay Switching Hub   

         

3.1 Installing the 9 Port NWay Switching Hub 

The SWH-2109F does not require software configuration. Users can immediately 

use any of the features of this product simply by attaching the cables and turning the 

power on. 

   

3.1.1 Desktop Installation 

To locate the switching hub on the desktop and place the hub on a clean, flat desk 

or table closes to a power outlet. Plug in all network connections and the power cord, and 

then the system is ready. 

 

When deciding where to put the switching hub then you must ensure: 

„

 

It is accessible and cables can be connected easily 

„

 

Power cord holder was kept in package if consider to fix power cord. It could lock 
aside from consol port. 

„

 

Cabling is away from: 

        Sources of electrical noise such as radios, transmitters and broadband amplifiers 

        , Power lines and fluorescent lighting fixtures. 

„

 

Water or moisture can not enter the unit 

„

 

Air flow around the unit and through the vents in the side of the case is not         

restricted (company recommend that you provide a minimum of 25mm inch 
clearance) 

To prolong the operational life of your units: 

Summary of Contents for SWH-2109FX













Reviews: