Cub Cadet 59A40003727, Operator'S Manual

10

seCTion 8: iniTial insTallaTion

TraCTor preparaTion

Remove the front weight bracket from the front of the tractor by re-
moving the six hex screws and nuts securing it to the front frame. 
Store the front weight bracket for reinstallation when removing the 
loader and attaching rear mounted equipment.

installing the LH and rH Mounts

iMPOrTanT:

the lH and RH mounts are heavy and awkward 

to handle. Usage of a lifting device (e.g. floor jack), or the aid of 
an assistant, while positioning the tower mounts for installation is 
recommended.

install the rH and LH mounts as follows:

•  Look at the RH mount (1) to note the configuration of the 

holes on the mounting plate of  the assembly. 

•  From the right side of the tractor, locate the three holes in a  

triangular pattern on the tractor’s clutch housing, and the two 
vertical holes on the front frame. Remove the protective plugs 

from the holes See Figure 3.

figure 3

iMPOrTanT:

When positioning the RH mount on the tractor, 

be especially careful to avoid damaging the small hydraulic lines 
running along the bottom of the frame. temporarily move the 
rubber hose out of the way.

•  Lift the RH mount (1) and carefully place against the tractor, 

aligning its holes with the holes in the tractors clutch housing 
and frame. 

•  Insert three hex cap screws (5) through the RH mount and 

thread into the clutch housing. Insert two hex cap screws (6) 
through the front of the mount and thread into the frame. In a 
staggered pattern, evenly tighten the five hex cap screws to 

secure the RH mount. Torque the screws to 145 - 167 ft. lbs. 
(196-225 N•M). Refer to Figure 3.

Hex Cap

Screw

RH Mount

Clutch

Housing

Front

Frame

Hex Cap

Screw

•  From the left side of the tractor, locate the mounting holes and 

remove the protective plugs.

•  Lift the LH mount (2) and carefully place against the tractor, 

aligning its holes with the holes in the tractors clutch housing 
and frame. 

•  Insert three hex cap screws (5) through the LH mount and 

thread into the clutch housing. Insert two hex cap screws (6) 
through the front of the mount and thread into the frame. In a 
staggered pattern, evenly tighten all hex cap screws to secure 

the LH mount. Torque the screws to 145 - 167 ft. lbs. (196-225 
N•M). Refer to Figure 3.

installing the Front Mount receiver

If not already done, remove the two lynch pins and withdraw the 
mounting pins to separate the front mount receiver from the loader 

hitch bracket (Refer to Figure 1).
•  Slide a flat washer (8) onto each of the eight hex cap screws 

(7). Refer to Figure 4.

•  Position the front mount receiver (3) so that its open channel 

is facing downward. Then place the front mount receiver 
against the front of the tractor frame (where the front weight 
bracket was previously removed). 

•  Align the eight holes in the front mount receiver with the 

corresponding holes in the front frame. While holding the 

front mount receiver in position, insert eight hex cap screws 
w/washers through the front mount receiver and tractor frame. 

See Figure 4.

figure 4

•  Thread a hex lock nut (9) onto each hex cap screw. In a 

staggered pattern, evenly tighten all hex cap screws and lock 

nuts. Torque the fasteners to 60-70 ft. lbs. (81-94 N•M)

Hex Cap

Screw

Flat Washer

Hex Lock Nut

Front Mount

Receiver

Front

Frame