Operation
22
769-12285
EN
Wheels (Fig .
E
)
Use the wheels to obtain a clean and uniform cut.
WArNING!
Risk of injuries due to the cutting tool.
¾
Only adjust the device with the motor
switched off and the cutting tool at a
standstill.
¾
Do not reach into the area of the rotating
line.
¾
Always remove the power pack prior to
working on the device.
Î
Press the bracket
Ag
on to the telescopic
arm
E
1
.
Î
Open the lever on the bracket
E 3
.
Î
Push the adapter
Aa
from above into the bracket
until it engages
E
2
.
Î
Push the wheels
Ah
from above into the adapter
until they engage
E
4
.
Î
Push the wheels into the desired height posi-
tion
E 5
.
Î
Reverse the lever of the bracket to secure the
wheels at the set height
E 6
.
operation
Adjusting the length of the telescopic arm
(Fig .
F
)
Î
Undo the threaded sleeve
F 1
.
Î
Pull the telescopic arms apart, until the ideal
handle length is obtained
F 2
.
Î
Tighten the threaded sleeve
F 3
.
Adjusting the middle handle (Fig .
G
)
Î
Undo the locking lever on the middle handle
G 1
.
Î
Push the middle handle to the desired height
G 2
.
Î
Adjust the inclination of the middle handle
G 3
.
Î
Clamp the locking lever
G 4
.
Inserting the power pack (Fig .
H
)
WArNING!
Incorrect handling of the power pack and
the charger
Â
Risk of injuries and material damage
¾
Read and observe the operating instruc-
tions of the power pack and the charger.
The 2-stage latching mechanism is used to set oper-
ating or transport mode of the power pack.
Position 1
H
1
3
The power pack is in transport mode.
•
Electrical contacts are open to prevent the pow-
er pack from inadvertently self-discharging.
Position 2
H
2
3
The power pack is in operating mode.
•
The electrical contacts are closed and the de-
vice is ready for use.
Switching the device on (Fig .
I
)
Î
Press and hold the right or left releasing de-
vice
I
1
.
Î
Press and hold the on/off button
I
2
.
3
The device operates.
Adjusting the line (Fig .
J
)
Automatic
With each switching off and on the line is adjusted
out of the line cassette.
Note
If the cutting line becomes too short during
operation due to wear, switch the device off
and then back on again to extend the working
length of the cutting line automatically.
Manual
WArNING!
Risk of injuries due to the cutting tool.
¾
Only adjust the device with the motor
switched off and the cutting tool at a
standstill.
¾
Do not reach into the area of the rotating
line.
¾
Always remove the power pack prior to
working on the device.
cAUtIoN!
Risk of injury on the cutting device that is
used for shortening the line length.
¾
After pulling out new line, always hold
the device in its normal working position
before you switch it on.
Manual line adjustment may be necessary during
first use, after adjustment of the plastic knife or after
changing the coil spool.
Î
Press the red knob
J 1
.
Î
Pull the line out on both sides
J 2
.
Note
Frequently switching on and off without
reason results in increased line wear.
Summary of Contents for 769-12285
