background image

13

1.

ENGINE /TRANSMISSION CRADLE: 
DESCRIPTION

The engine and transaxle are supported by a single 
structure that pivots on a “dogbone” link that connects 
the front of the cradle to the frame.  The cradle and 
transaxle function as the Big County’s rear suspension.  
The engine must be held in a stable position in relation 
to the transaxle, in order to maintain tension on the 
drive belt.   The engine is mounted to the cradle, and 
moves with the suspension.

2.

“DOGBONE” LINK ASSEMBLY

2.1.

Make a visual inspection of the link assembly at 
each engine oil change interval (200 hrs), or if 
any clunking noise is noticeable from the joint.

2.2.

The joint consists of  a metal body with two rub-
ber bushings.  The bushings allow the cradle to 
swing up and down, and to pivot.  

2.3.

The life of the bushings will vary with tempera-
ture and severity of usage.

2.4.

The joint can be replaced without removing the 
cradle.

NOTE: 

 The bolt and nut connecting the link to 

the frame are SAE.  The bolt and nut connecting 
the cradle to the link are metric.

3.

TRANSAXLE MAINTENANCE

3.1.

Brake system maintenance is covered sepa-
rately in the Brake System section of this man-
ual.

3.2.

The electrically controled, vacuum actuated gear 
selector system is covered in the Gear Selector 
section of this manual.

3.3.

Lubrication intervals

: Change the oil in the 

transaxle after the first 50 hrs. of use.  After this 
break-in service is performed change the tran-
saxle oil every 24 months or 500 hrs. of use.

3.4.

If the oil in the transaxle becomes contaminated, 
change it immediately

3.5.

To drain the oil from the transaxle, remove the 
hex-head plug that is located at the bottom of the 
left side of the transaxle housing, directly below 
the left axle tube.  

NOTE: 

Clean the area surrounding the drain 

plug before removal.

3.6.

Check the oil level in the transaxle every 100 
hrs. of use.  If any leakage is evident, check the 
level more frequently until the Big Country 4 X 2 
can be taken to an authorized Cub Cadet dealer 
for repair.

4 X 2 Drive Package: Dana Transaxle

Summary of Contents for BIG COUNTRY 4X2







































Reviews: