background image

9

9

7

8

3-4

 Reinstallation

Right indicator goes to right side A-pillar through the left side A-pillar and 
then the ceiling. The installation height and method is the same with the 
left one. 

Please ensure to hide all the wires properly into the trims and frame's 
waterproof strips to avoid the wiring harness from affecting driving safety, 
and obstructing you from getting in and off the car. Besides please hide 
the splitter into the trim under the instrument panel properly and use 
cable ties to fix with the car cables.

Plug into Cigarette lighter and hide the remaining wires properly. When 
ACC ON, the indicators will light up for 3 seconds, and the buzzer will 
chime once, indicating that the system has started normally.

If the bracket is incidentally attached wrongly, such as not at the center 
of the rear windshield, not close to the upper edge of the rear windshield, 
or not maintained at a horizontal level, etc., and you wish to remove 
and reattach, spray alcohol around the bracket base in contact with 
rear windshield. Then use a thin line such as a fishing line to scrape the 
edges of the bottom back and forth.

Summary of Contents for VS-95A043

















Reviews: