background image

This manual should be read and understood by all personnel who 
operate or service this PVC heater. Failure to understand how to safely 
operate and service this unit could result in injury or death. This unit 
should only be operated by qualified personnel.

RETAIN SAFETY INFORMATION

SPECIFICATIONS — 453 PVC Heater

Model No.

453   Automatic Rotation

Capacity

1

/

2

” to 6” PVC conduit

Power

230 volts AC - Single Phase, 28 amps, 60 hz, 6400 watts

Dimensions

11 

5

/

8

”  x 15 

7

/

8

” x 74”

Weight

72 lbs.

B E N D I N G

MATERIALS NEEDED

• Sponge or clean cloth

• Bucket with clean water

• Insulated gloves

IMPORTANT SAFETY INFORMATION

• ALWAYS wear hand protection when operating this equipment and when 

bending PVC conduit. Use handle to open and close the PVC heater door(s).

• DO NOT use in wet conditions. DO NOT expose to rain or moisture.

• DO NOT use near flammable materials.

• DO NOT leave PVC heater unattended.

• Turn PVC heater off when not in use.

• Use for heating PVC conduit only. DO NOT use for any other purpose.

• Use only for PVC conduit sizes specified.

• Operate only in a well ventilated area.

• Use only with a grounded power source.

2

ELECTRIC SHOCK HAZARD! Only connect this

receptacle. Do NOT modify the plug which is
provided with the unit. Failure to follow these
warnings can result in serious injury or death.

WARNING

RECEPTACLE

LOCKING PLUG

The electric plug on this PVC heater
includes a grounding conductor and 
is the twist to lock type as shown. 
Only connect the unit to a 30 AMP
receptacle  which is properly installed
and grounded to meet all applicable
electrical codes. Do NOT remove or
modify the plug in any way.

Summary of Contents for 453






Reviews: