GB-1
GB-2
UNPACKING
Remove all packaging from the unit. Retain the packaging. If you
dispose of it please do so according to any local regulations.
The following items are included:
PRODUCT OVERVIEW
CONTROL PANEL
Do not operate without both feet attached. Only operate the radiator in
an upright position (feet on the bottom, controls on the top), any other
position could create a hazardous situation.
Do not immerse the radiator in water. Do not use any cleaning chemicals
such as detergents and abrasives. Do not allow the interior to get wet as
this could create a hazard.
GB-3
OVERHEAT PROTECTION SYSTEM
The power to the radiator will automatically cut off if the temperature of
the heater exceeds a certain limit. In the event of overheating, the radiator
will stop operating. Switch the radiator off and allow it to completely cool.
The radiator will then operate again as normal.
CLEANING AND STORAGE
1. Always remove the mains plug
from the mains socket and allow
the radiator to cool down before
cleaning the radiator.
2. Wipe the radiator with a soft damp
(not wet) cloth.
3. Store the radiator in a clean dry
place.
HINTS & TIPS
My radiator does not work when I turn it on
1. Check that your radiator is plugged in and the power is turned on at the
mains socket.
2. Set the temperature to the highest setting.
3. Check if the thermostat setting is too low.
4. Try replacing the BSI or ASTS approved 13 Amp BS1362 fuse in the plug.
5. If the radiator still doesn’t work, do not try to repair the radiator
yourself.
If your radiator’s power is automatically cut off follow the steps
below:
1. Unplug your radiator and allow it to cool down.
2. Inspect your radiator.
3. Plug-in the radiator and switch it on again. If it cuts off again, move the
radiator to a better ventilated location.
4. If there is any sign of physical damage (e.g. melting, or burning of the
case), do not attempt to use your radiator. Please leave all maintenance
work to qualified personnel.
ASSEMBLY
1. Unpack the radiator and remove all the parts from the packaging.
2. Place the radiator body upside-down on a scratch-free surface, making
sure it is stable and will not fall.
3. Insert the front foot horizontally into the bottom of the front cover until
it clips into place.
4. Insert the rear foot vertically along the rear fin and press it down until it
is firmly fitted .
OPERATION
1. Position the radiator upright on the floor away from curtains, furniture or
wallcovering before plugging your radiator into the mains socket.
2. Switch the
Power Switch
to the ON position.
3. Turn the
Thermostat Control
to the desired position. It is recommended
to rotate to “MAX” position to get the radiator to pre-heat. It will take
5-10 minutes for the radiator to pre-heat.
4. When the room reaches the desired temperature, turn the
Thermostat
Control
slowly anti-clockwise until the power indicator goes off with a
“click” sound. The radiator will temporarily go off.
5. If the room temperature falls below the desired temperature, the
radiator and power indicator will turn on again until the room tempera-
ture reaches the desired temperature.
If items are missing or damaged, please contact Partmaster (UK only).
Tel: 0844 800 3456 for assistance.
The Main Unit
Rear Foot
(P.N.: AI1087H08R)
Instruction Manual
(P.N.: C7MOR10-002)
I
0
MIN
MAX
POWER
Front Foot
(P.N.: AI1117H08R)
700W MINI
OIL FILLED RADIATOR
INSTRUCTION MANUAL
C7MOR10
Thank You for purchasing your new Currys Essentials
700W Mini Oil Filled Radiator.
We recommend that you spend some time reading this instruction
manual in order to fully understand all the operational features it offers.
Read all the safety instructions carefully before use and keep this
instruction manual for future reference.
I
0
MIN
MAX
POWER
I
0
MIN
MAX
POWER
Radiator Fins
Front Foot
Front Cover
Pilot Light
Carry Handle
Rear Foot
0
I
MIN
MAX
Thermostat
Control
Power Switch
C
M
Y
CM
MY
CY
CMY
K
C7MOR10_IB_110615.pdf 2 15/06/2011 12:03 PM
