Custom Crimp D105 Series Operator'S Manual Download

Page: 3 / 26

D105

Service Hose Crimper

SAFETY PRECAUTIONS-----------------------------------------------------------------------------------------------------2

COMPONENT PARTS & TECHNICAL DATA--------------------------------------------------------------------------------------------------4

FEATURES------------------------------------------------------------------------------------------------------------------------5

INITIAL SET UP-------------------------------------------------------------------------------------------------------------------------------6

LUBRICATION PROCEDURE-------------------------------------------------------------------------------------------------------7

CRIMPING PROCEDURE---------------------------------------------------------------------------------------------------8

CALIBRATION CHECK PROCEDURE---------------------------------------------------------------------------------------------13

D105 / D165 D-SERIES DRAWER ASSEMBLY / STAND (INSTRUCTIONS)------------------------------------------------------15

INCLUDED ACCESSORIES----------------------------------------------------------------------------------------16

AVAILABLE ACCESSORIES----------------------------------------------------------------------------------------17

TROUBLESHOOTING---------------------------------------------------------------------------------------------------------18

COMPONENT PARTS BREAKDOWN--------------------------------------------------------------------------------------------19

CUSTOMCRIMP® “NO-NONSENSE” WARRANTY STATEMENT---------------------------------------------------------------25

CUSTOMCRIMP® CONTACT INFORMATION--------------------------------------------------------------------------------------26

TABLE OF CONTENT

Summary of Contents for D105 Series



























Search results

Summary of Contents for D105 Series

Reviews:

Related manuals for D105 Series

Brands by name

Popular brands

Custom Crimp D105 Series, Operator'S Manual

Search results

Summary of Contents for D105 Series

Reviews:

Related manuals for D105 Series

Brands by name

Popular brands