Operations Guide
931281I
CyberData Corporation
Local SIP Port
The Local SIP Port is the port number the device will use to receive SIP messages for
the Nightringer extension. This value cannot be the same as the
for
the primary extension. The default Local SIP Port is 5061. The supported range is 0-
65536. Enter up to 5 digits.
Outbound Proxy
Enter the Outbound Proxy address as an IPv4 address in dotted decimal notation or a
fully qualified domain name (FQDN). When an IP address is configured, the device
will send all SIP messages to this IP address for the Nightringer extension. When an
FQDN is configured, the device will run DNS NAPTR, SRV, and A queries on the
FQDN to resolve an IP address to which it will send all SIP messages for the
Nightringer extension. This field can accept entries of up to 255 characters in length.
Outbound Proxy Port
The Outbound Proxy Port is port number used as the destination port when sending
SIP messages to the outbound proxy for the Nightringer extension. A value of 0 will
default to 5060. The supported range is 0-65536. Enter up to 5 digits.
User ID
Specify the SIP User ID for the SIP server. This parameter becomes the user portion
of the SIP-URI for the device's Nightringer extension. Enter up to 64 alphanumeric
characters.
Authenticate ID
Specify the Authenticate ID for the SIP Server. This parameter is required for SIP
registration authentication. Enter up to 64 alphanumeric characters.
Authenticate Password
Specify the Authenticate Password for the SIP Server. This parameter is required for
SIP registration authentication. Enter up to 64 alphanumeric characters.
Re-registration Interval (in seconds)
The SIP Re-registration Interval (in seconds) is the SIP Registration lease time, also
known as the expiry. The supported range is 30-3600 seconds. Enter up to 4 digits.
Nightringer Strobe Settings
The following strobe settings will only appear if you are using the Strobe Kit. If
you are not using the Strobe Kit, you will not see the strobe settings.
Blink Strobe on Nightring
When selected, the Strobe will blink a scene when the Nightringer is ringing.
Scene
Select desired scene (only one may be chosen).
ADA Compliant
Strobe will blink ON at the specified brightness for 150ms then OFF for 350ms during
the duration of the event.
Slow Fade
Strobe will increase in brightness from 0 to the specified brightness and back to 0 over
the course of about 3.5 seconds during the duration of the event.
Fast Fade
Strobe will increase in brightness from 0 to the specified brightness and back to 0 over
the course of about 1.5 seconds during the duration of the event.
Slow Blink
Strobe will blink ON at the specified brightness for one second then OFF for one
second during the duration of the event.
Fast Blink
Strobe will blink ON at the specified brightness then OFF five times per second during
the duration of the event.
Color
Select desired color (only one may be chosen).
Brightness
How bright the strobe will blink when the Nightringer is ringing. This is the maximum
brightness for “fade” type scenes.
Red
The red LED value for Nightringer.
Green
The green LED value for Nightringer.
Blue
The blue LED value for Nightringer.
Use this button to preview the strobe flashing behavior for the
Nightringer Strobe
Settings
.
Table 2-17. SIP Page Parameters (continued)
Web Page Item
Description
Summary of Contents for InformaCast Enabled 011406
Page 80: ...Operations Guide 931281I CyberData Corporation Figure 2 41 SSL Configuration Page ...
Page 81: ...Operations Guide 931281I CyberData Corporation Figure 2 42 SSL Configuration Page ...
Page 90: ...Operations Guide 931281I CyberData Corporation Figure 2 47 Audiofiles Page ...
Page 91: ...Operations Guide 931281I CyberData Corporation Figure 2 48 Audiofiles Page ...
