BR650ELCD / BR850ELCD
User’s Manual
K01-0000180-00
This manual contains important instructions that should be followed during installation and maintenance of
the UPS and batteries. Please read and follow all instructions carefully during installation and operation of
the unit. Read this manual thoroughly before attempting to unpack, install, or operate.
CAUTION!
The UPS must be connected to a grounded AC power outlet with fuse or circuit breaker
protection.
DO NOT
plug the UPS into an outlet that is not grounded. If you need to de-energize this
equipment, turn off and unplug the UPS.
CAUTION! DO NOT USE FOR MEDICAL OR LIFE SUPPORT EQUIPMENT!
CyberPower Systems does
not sell products for life support or medical applications.
DO NOT
use in any circumstance that would affect
the operation or safety of any life support equipment, with any medical applications, or patient care.
CAUTION!
The battery can energize hazardous live parts inside even when the AC input power is
disconnected.
CAUTION!
To prevent the risk of fire or electric shock, install in a temperature and humidity controlled indoor
area, free of conductive contaminants. (Please see specifications for acceptable temperature and humidity
range).
CAUTION!
To reduce the risk of electric shock, do not remove the cover, except to service the battery. There
are no user serviceable parts inside, except for the battery.
CAUTION!
To avoid electrical shock, turn off the unit and unplug it from the AC power source before
servicing the battery or installing a computer component.
CAUTION! DO NOT USE WITH OR NEAR AQUARIUMS!
To reduce the risk of fire, do not use with or near
aquariums. Condensation from the aquarium can come in contact with metal electrical contacts and cause
the machine to short out.
UNPACKING
The box should contain the following:
(1) UPS Unit x 1; (2) Phone Line x 1; (3) USB Cable x 1; (4) User Manual x 1; (5) Management software
Disk x 1; (6) Cable Collector x 1
OVERVIEW
The BR650ELCD/BR850ELCD provides automatic voltage regulation for inconsistent utility power. The
BR650ELCD/BR850ELCD features 405 Joules of surge protection, and provides battery backup during
power outages. The BR650ELCD/BR850ELCD ensures consistent power to your computer system and its
included software will automatically save your open files and shutdown your computer system during a utility
power loss.
HOW TO DETERMINE THE POWER REQUIREMENTS OF YOUR EQUIPMENT
1.
Make sure that the total Volt-Amp (VA) requirements of your computer, monitor, and peripheral
equipment does not exceed 650VA/850VA.
2.
Ensure that the equipment plugged into the battery power-supplied/surge outlets does not exceed the
UPS unit's rated capacity (650VA/390W for BR650ELCD, 850VA/510W for BR850ELCD). If the rated unit
capacities are exceeded, an overload condition may occur and cause the UPS unit to shut down or the
circuit breaker to trip.
HARDWARE INSTALLATION GUIDE
1. Your new UPS may be used immediately upon receipt. However, after receiving a new UPS, to ensure the
battery’s maximum charge capacity, it is recommended that you charge the battery for at least 8 hours.
Your UPS is equipped with an auto-charge feature. When the UPS is plugged into an AC outlet, the
battery will automatically charge whether the UPS is turned on or turned off.
2. If you will use the software, connect the USB cable to the USB port on the UPS.
3. With the UPS unit off and unplugged, connect the computer, monitor, and any externally powered data
storage device (Zip drive, Jazz drive, Tape drive, etc. into the battery power supplied outlets.
DO NOT
plug
a laser printer, copier, space heater, vacuum, paper shredder or other large electrical device into the
battery power supplied outlets. The power demands of these devices will overload and possibly damage
the unit.
4. To protect a fax, telephone, modem line or network cable, connect a telephone cable or network cable
from the wall jack outlet to the IN jack of the UPS. Then connect a telephone cable or network cable from
the OUT jack on the UPS to the modem, computer, telephone, fax machine, or network device.
5. Plug the UPS into a 2 pole, 3 wire grounded receptacle (wall outlet). Make sure the wall branch outlet is
protected by a fuse or circuit breaker and does not service equipment with large electrical demands (e.g.
air conditioner, refrigerator, copier, etc. Avoid using extension cords.
6. Depress the power switch to turn the unit on. The power on indicator light will illuminate and the unit will
"beep".
7. If an overload is detected, an audible alarm will sound and the unit will emit one long beep. To correct this,
turn the UPS off and unplug at least one piece of equipment from the battery power supplied outlets. Wait
10 seconds. Make sure the circuit breaker is depressed and then turn the UPS on.
8. To maintain optimal battery charge, leave the UPS plugged into an AC outlet at all times.
9. To store your UPS for an extended period, cover it and store with the battery fully charged. Recharge the
battery every three months to ensure battery life.
DESCRIPTION
Power On/Off Switch
Press the power switch to turn the UPS ON or OFF.
LCD Function Selected Switch
Press the LCD function selected switch to know the UPS status.
LCD Display
The LCD will display the UPS status including input voltage, output voltage, runtime, percentage of load
and battery, etc.
Communication Protection Ports RJ11/RJ45
Communication protection ports will protect any standard modem, fax, telephone line, or network cable
from surge and spikes.
AC outlets
The UPS provides 3 outlets for connected equipment to insure temporary uninterrupted operation during
a power failure and against surges and spikes and another 3 outlets against surges and spikes only.
USB Port to PC
This port allows connection and communication
from the USB port on the computer to the UPS unit.
The UPS communicates its status to the
PowerPanel
®
Personal Edition
software.
Input Circuit Breaker
The Circuit Breaker provides optimal overload
protection.
Power on LED
The power on LED lights up when the UPS is ON.
Cable Collector
Collect the cables connected from the AC outlets in the cable collector.
Model
BR650ELCD
BR850ELCD
Capacity (VA)
650VA
850VA
Capacity (Watts)
390W
510W
Input
Input Voltage Range
160-265Vac
Frequency Range
47~63Hz (Auto Sensing)
AVR Function
Boost @ 200+/-10V
Output
On Battery Output
Voltage
Simulated Sine Wave at /-10%
On Battery Output
Frequency
50/60Hz +/-1%
Transfer Time
4ms Typical
Overload Protection
On Utility: Circuit Breaker and Internal Current Limiting
On Battery: Internal Current Limiting
Surge Protection
Lightning / Surge
Protection
Yes
Network/ Phone/ Fax/
Modem Protection
RJ11/RJ45 (One In/ One Out)
Operating Temperature
0
°
C to 40
°
C
Operating Relative
Humidity
0 to 90% non-condensing
Physical
Total # of UPS outlets
6 (3 for battery backup and surge, 3 for surge)
Maximum
Dimensions(LxWxH)
271 x 160.7 x 113.6mm
Weight (kg)
5.5
6.4
Battery
Sealed Maintenance
Free Lead Acid Battery
12V / 7Ah x1
12V / 8.5Ah x1
Typical Recharge Time
8 hours
User Replaceable
Yes
Status Indicators
Indicators
Power On, LCD Display
Audible Alarms
On Battery, Low Battery, Overload
Communication
PowerPanel
®
Personal
Edition Software
Windows 7/Vista/XP/2000/Server 2003, Linux
Management
Auto-Charger
Yes
Auto-Restart
Yes
USB interface
Yes
TECHNICAL SPECIFICATIONS
BASIC OPERATION
INSTALLING YOUR UPS SYSTEM
IMPORTANT SAFETY INSTRUCTIONS
