CAUTION!
Read and follow the
IMPORTANT SAFETY INSTRUCTIONS
before servicing the battery.
Service the battery under the supervision of personnel knowledgeable of
batteries and their
precautions.
CAUTION!
Use only the specified type of battery. See your dealer for replacement batteries.
CAUTION!
The battery may present the risk of electrical shock. Do not dispose of batteries in a fire, as they
may explode. Follow all local ordinances regarding proper disposal of batteries.
CAUTION!
Do not open or mutilate the batteries. Released electrolyte is harmful to the skin and eyes and
may be toxic.
CAUTION!
A battery can present a high risk of short circuit current and electrical shock. Take the following
precautions before replacing the battery:
1. Remove all watches, rings or other metal objects.
2. Only use tools with insulated handles.
3.
DO NOT
lay tools or other metal parts on top of battery or any battery terminals.
4. Wear rubber gloves and boots.
5. Determine if the battery is inadvertently grounded. If inadvertently grounded, remove source of ground.
CONTACT WITH A GROUNDED BATTERY CAN RESULT IN ELECTRICAL
SHOCK!
The likelihood of
such shock will be reduced if such grounds are removed during installation and maintenance (applicable to a
UPS and a remote battery supply not having a grounded circuit)
BATTERY REPLACEMENT PROCEDURE
1. Turn off and unplug all connected equipment.
2. Turn the UPS off and unplug it from the AC power source.
3. Turn the UPS on its side.
4. Remove the retaining screw located on the bottom of the UPS.
5. Slide the battery compartment cover completely off of the unit.
6. Remove the batteries from the compartment.
7. Disconnect the battery wires from the batteries.
8. Install the replacement batteries by connecting the red wire (+) and black wire (-) to the same color
connectors from the battery pack.
9. Put the batteries back into the compartment.
10. Slide back the battery compartment cover and tighten the retaining screw.
11. Recharge the UPS for 8-16 hours to fully charge the battery.
BR700ELCD/ BR1000ELCD
BR1200ELCD
LCD Indication
Line Mode
Display SW
Press
UPS Status Display
Capacity Display
Digital Value Display
Load
Cap.
Battery
Cap.
Input
Voltage
Output
Voltage
Run
Time
%
of
Load
%
of Batt.
Initial
V X -- X V X
V
1st V
X
--
X
V X V
2nd
V X -- X V X
V
3rd
V X -- X X V
V
4th
V X -- X V X V
5th(Return) V X -- X V X
V
Press >3sec
(Sound Disable)
V
X
V
X -- -- -- -- -- -- --
Press >3sec
again
(Sound Enable)
V
X
X
X -- -- -- -- -- -- --
(Overload) V
X
--
V -- -- -- -- --
--
--
“V” : Illuminated, “X” : Not Illuminated, “--“ : Either
Battery Mode
Display SW
Press
UPS Status Display
Capacity Display
Digital Value Display
Load
Cap.
Battery
Cap.
Input
Voltage
Output
Voltage
Run
Time
%
of
Load
%
of Batt.
Initial
X V -- X X V
V
1st X
V
--
X
X V V
2nd
X V -- X V X
V
3rd
X V -- X X V
V
4th
X V -- X X V V
5th(Return) X V -- X X V
V
Press >3sec
(Sound Disable)
X
V
V
X -- -- -- -- -- -- --
Press >3sec
again
(Sound Enable)
X
V
X
X -- -- -- -- -- -- --
(Overload) X
V
--
V -- -- -- -- --
--
--
“V” : Illuminated, “X” : Not Illuminated, “--“ : Either
CyberPower’s Green Commitment
CyberPower is dedicated to the development of green products, and has adopted
Green practices throughout its business, including: membership in Climate Savers
Computing Initiative (CSCI), accordance with the Restriction on Hazardous
Substances (RoHS), Waste Electrical and Electronic Equipment (WEEE) protocols,
as well as ISO 14001 and IECQ QC080000. CyberPower pledges to provide the
advanced energy solution for the environment and become a leading eco-friendly
organization in the UPS industry.
Reduce Energy Cost with GreenPower UPS
TM
Technology
CyberPower’s goal is not only to provide eco-friendly products but also to bring the best value for consumers.
The advanced energy-saving design improves the operating efficiency and eliminates waste energy
consumption
.
As a result, consumers will enjoy significant energy cost savings with the adoption of
GreenPower UPS
TM
technology.
Problem
Possible Cause
Solution
Full-time surge protection
outlets stop providing power
to equipment. Circuit
breaker button is projecting
from the side of the unit.
Circuit breaker has
tripped due to an
overload.
Turn the UPS off and unplug at least one
piece of equipment. Wait 10 seconds, reset
the circuit breaker by depressing the button,
and then turn the UPS on.
The UPS does not perform
expected runtime.
Battery not fully
charged.
Recharge the battery by leaving the UPS
plugged in.
Battery is slightly worn
out.
Contact CyberPower Systems about
replacement batteries.
The UPS will not turn on.
The on/off switch is
designed to prevent
damage by rapidly
turning it off and on.
Turn the UPS off. Wait 10 seconds and then
turn the UPS on.
The battery is worn out.
Contact CyberPower Systems about
replacement batteries
Mechanical problem.
Contact CyberPower Systems at
www.cyberpower.com
PowerPanel® Personal
Edition is inactive.
The USB cable is not
connected.
Connect the USB cable to the UPS unit and
an open serial port on the back of the
computer. You must use the cable that came
with the unit.
The unit is not providing
battery power.
Shutdown your computer and turn the
UPS off. Wait 10 seconds and turn the
UPS back on. This should reset the unit.
Additional troubleshooting information can be found at
www.cyberpower.com
For more information, Visit
www.cyberpower.com
or contact
CyberPower Systems B.V.
All rights reserved. Reproduction without permission is prohibited.
6F, No. 32, Sec. 1, Chenggong Rd., Nangang District, Taipei 115, Taiwan
TROUBLESHOOTING
DEFINITIONS FOR ILLUMINATED LCD INDICATORS
CYBERPOWER GREENPOWER UPS™ TECHNOLOGY
BATTERY REPLACEMENT
