background image

 

 

Installation Instructions 

Amplified Handlebar Speaker Kits 

 

Note:

 Audio quality is also dependent upon the device with which the amplifier is 

being used with. For best results Cycle Sounds recommends that you use an 
audio source with a high millivolt output such as an iPod or modern Smart Phone. 
Also adjusting the equalizer for the type of music being played will make your 
product work and sound better as well. See 

STEP-10

 for more information. 

 
All Cycle Sounds products have a warranty period of 1 year from the date of 
original purchase. This warranty covers the cost of parts only for any needed 
repairs to, or replacement of, your unit for 1 year under normal usage. (Labor for 
removal or reinstallation of speaker kits and shipping cost are not covered by this 
warranty). Any product modified from its original manufactured form or installed 
improperly, shall not be covered by this warranty. This does not include 
modifications that are required for normal installation as outlined in the 
instructions below. Specifically, you should not cut any wires, remove quick 
connectors or cut/bend brackets or you risk voiding the manufacturer

ʼ

s warranty. 

 

Warranty Notice

 - When returning products for warranty service a copy of the 

original sales receipt or proof of purchase must be sent in the package 
accompanying the product. Failure to do so will delay your warranty service.  
 
 

Warning:

 The use of a radio, iPod, MP3 player, satellite radio, or any other 

device on a motorcycle increases the risk of riding. Riders must always pay 
attention while operating their motorcycles. Always make volume and tuning 
adjustments when motorcycle is not in motion. Failure to not do so could result in 
serious or fatal injuries.

  

 

Failing to follow all installation instructions and recommendations carefully can 
result in damage to your product, damage to your motorcycle, personal injury or 
even death. 

 

Summary of Contents for Handlebar Speaker













Reviews: