background image

CYNTEC CO., LTD.

乾坤科技股份有限公司

乾坤科技股份有限公司

乾坤科技股份有限公司

乾坤科技股份有限公司

DOCUMENT  : RFB00000

REVISION    : A0

PAGE                : 11 OF 11

13.

 

Restrictions on Application:
If the components should be used in application that required extremely high reliability, contact
Cyntec before use.

z

 

Space activities (Man-made satellite, Rocket etc.)

z

 

Submarine activities (Relay station, Submarine equipment)

z

 

Military activities

z

 

Units related to safety and control of transportation vehicles (Automobile,    Airplane, Train, etc.)

z

 

Controllers for power plants (Atomic energy power, Hydro-electric power, Thermal power)

z

 

Medical equipment directly related to the support of human life (Life-supporting device, Cardiac
defibrillator, Artificial dializer, etc.)

z

 

Information processing system (support computer, etc.)

z

 

Another application similar to the above.

14.

 

Warning
14-1

 

It shall be understood that this specification is to warrant the quality of the component solely, not
being mounted on the circuit of your set. The electrical performance of the component may vary
depending on the conditions where this component is mounted (e.g. circuit patterning, condition
of ground pattern. Etc.). Thai component, therefore, shall be preliminarity evaluated under your
designed circuit conditions prior to your actual use of this component.

14-2

 

Cyntec shall be free from any liability and damage which you may suffer as a result of your use
this component under any conditions not specified or described in this specifications.

           

Summary of Contents for TFP-21-S-140-B












Reviews: