background image

198 Champion Ct., San Jose, CA 95134

408.943.2600, 

www.cypress.com

If you have questions, call the

Applications Hot Line 425.787.4814

www.cypress.com/support

©2008 Cypress Semiconductor Corporation

Doc. # 001-44863 Rev. *A

CapSense™, PSoC Designer™, Programmable System-on-Chip™, and PSoC Express™ are trademarks
and PSoC® is a registered trademark of Cypress Semiconductor Corp. All other trademarks or registered
trademarks referenced herein are property of the respective corporations.

Additional CapSense Kits

For more information on these kits, please go to 

www.cypress.com/CapSense

.

Evaluation Kits

Development Kit

CapSense 

Express: 

Quickest 

and Easiest to Use 

Touch Sensing

CY3218

CAPEXP1/CAPEXP3

For Buttons

(Up to 10 or 4 IOs)

CY3218

CAPEXP2

For Sliders

(Up to 10 IOs)

CY3280-BK1

Universal CapSense

CapSense: 

Programmable 

Touch Sensing

CY3203A

CapSense CSA

CapSense Plus: 

CapSense with Non-

Touch Sensing 

Functionality (Motor 

Control, Power 

Management, Gyro 

Sensing, etc.)

CY3213A

CapSense CSD

CY3214

PSoCEvalUSB

Doc. # 001-44863 Rev. *A

Cypress Semiconductor

198 Champion Court

San Jose, CA 95134-1709

Phone (USA): 800.858.1810

Phone (Intnl): 408.943.2600

http://www.cypress.com

CY3218-CAPEXP2 CapSense™ Express

Evaluation Kit Quick Start

Summary of Contents for CapSense Express CY3218-CAPEXP2





















Reviews: