background image

 

4

 

 

231-914-0001-EN5 

IMPORTANT SAFETY INSTRUCTIONS 

 

 

Read, keep and follow these instructions.

 

 

Heed all warnings:

 

 

 

 
 
 
 
 

 

 

 

 

 

 
 
 
 
 
 
 
 
 
 

 

 

 

 
 

Owners and/or users of this D-BOX Haptic System are responsible for the dissemination of this information to all 
such persons named herein. Each owner and/or user of this D-BOX Haptic System agrees to evaluate and bear all 
risks associated with the use of this D-BOX Haptic System for themselves and for any subsequent users of this D-
BOX Haptic System and any subsequent users of this D-BOX Haptic System shall be deemed to be using this D-
BOX Haptic System under the direct supervision of such owner/user and such owner/user will be deemed to have 
communicated this advisory to all person described herein. 

 

D-BOX Technologies Inc. is in no way responsible for any damages of any kind arising from the use of  this  D-
BOX Haptic System and  the  owners  and/or  users  of  this  D-BOX Haptic System hereby agree not to hold D-
BOX Technologies Inc. responsible for any and all damages of any kind arising from the use of this D-BOX Haptic 
System including, but not limited to direct or indirect, punitive, incidental, special or consequential damages 
arising out of or in any way connected with the use of this D-BOX Haptic System. 

 

 

This D-BOX Haptic System may be harmful to 
women who are pregnant, persons with heart 

conditions, the elderly, or those with other pre-

existing medical conditions. All such persons 

should consult their physicians before using this 

D-BOX Haptic System. 

Use of this D-BOX Haptic System is not 

recommended for children under the age of ten 
years old without adult supervision. Owners 

and/or users of this D-BOX Haptic System should 

consult and comply with the user guide enclosed 

herein.

 

Use  of  hot  liquids  in  the  vicinity  of  this  D-

BOX Haptic System should  always be avoided 

to prevent spillage which could cause serious 
injuries to the user.

 

Use of this D-BOX Haptic System is a risk to hands 

and feet. Do not put hands or feet underneath the 
seat or near the haptic system. This may lead to 

serious injury. 

 

Do not use this device near water.

 

Do not install near any heat sources such as 

radiators, heat registers, stoves or any other 

appliances (including amplifiers).

 

Unplug this device during electrical storms or 

when unused for long periods of time.

 

Refer all servicing to qualified personnel. 
Servicing is required when the device has 

been damaged in any way. For example: if 

liquid has been spilled or objects have fallen 

onto it, if it has been exposed to rain or 

moisture, if it does not operate normally or, it 
has been dropped.

 

- Only clean the device with a dry cloth

 

- Do not block any ventilation openings. Install in      
   

accordance with the manufacturer’s 

 

   instructions. 

 

- Protect all the cables (USB, network, power,   
   etc.) from being walked on or pinched,   
   particularly at the ends.

 

 

- Use only attachments/accessories specified by  
   the manufacturer.

 

Summary of Contents for G5








































Reviews: