6/36
CPS-M1-MSE
English
99.828.70 1.2/07/22
Power packs PS-S1-24-20 and PS-S1-24-40
Functions:
•
Output: 24 V DC, 20 A or 40 A
• Installation on 35 mm top hat rail
•
Low ripple
• Reverse-voltage protected and short-circuit resistant
•
Multiple power supply units can be combined
•
For each power supply unit, one PSM supply module is needed
Technical data:
Type
PS-S1-24-20
PS-S1-24-40
Rated input voltage
230 V AC ± 15%
Frequency
45 to 65 Hz
Nominal power
530 VA / 480 W
1040 VA / 960 W
Output voltage
24 V DC ± 1%
Ripple
< 50 mVSS
Output current
20 A
40 A
Short-circuit resistant
YES
Can be connected in parallel YES
Reverse-voltage protected
YES
Input line connection
max. 6 mm² star / max. 4 mm² flexible
Output line connection
max. 6 mm² star / max. 4 mm² flexible
max. 16 mm² star / max. 16 mm² flexible
Dimensions WxHxD
90x130x150 mm
140x130x150 mm
Bistable relay module - BRM-1-COC-0006
• Six user-programmable, isolated change-over contacts,
for switching signals with 24 V DC or 230 V AC
• change-over contacts as bistable version
•
Definition of a switch-off state in the event of a mains and
battery failure possible (failsafe function)
•
Integrated LEDs to indicate a fault (yellow) and alarm
(red)
• Connection using removable spring-type terminals
•
Conductor cross-sections max. 2.5 mm² flexible
• Dimensions WxHxD: 26x130x125 mm
•
Installation on a 35 mm top hat rail in combination with
an expansion module socket
Digital I/O module - IOM-D1-1212
• 12 user-programmable digital inputs
• 12 user-programmable digital outputs
•
The digital inputs can also be parameterised as LT inputs
•
Integrated LEDs to indicate a fault (yellow) and alarm
(red)
• Connection using removable spring-type terminals
•
Conductor cross-sections max. 1.5 mm² flexible
• Dimensions WxHxD: 26x130x125 mm
•
Installation on a 35 mm top hat rail in combination with
an expansion module socket
Actuator module - AM-1-1-08-230-D4-D2
•
Module for connecting 230 V AC actuators
•
1 group for connecting drives with a total maximum
current of 8 A
• Up to 45 drives per AM 230 connectable
•
D+H 230 V AC drives with SHEV fast mode (HS) are
supported
•
The cable is monitored for breaks and short circuits
via the terminal module EM 230
• 2 user-programmable digital inputs (e.g. ventilation
button)
•
1 user-programmable digital output (e.g. NOT
CLOSED signal)
•
Can be used with 230 V AC standard drives
•
Adjustable ventilation time and opening width for
everyday ventilation
•
Integrated LEDs to indicate a fault (yellow) and alarm (red)
• Connection using removable spring-type terminals
•
Conductor cross-sections max. 2.5 mm² flexible
(230 V AC) or 1.5 mm² flexible (24 V DC)
• Dimensions WxHxD: 26x130x125 mm
•
Installation on a 35 mm top hat rail in combination with
an expansion module socket
AD I/O module - ADM-AD1-1212-4
• 4 user-programmable multifunctional inputs (digital or
analog)
• 8 user-programmable digital inputs
• 12 user-programmable digital outputs
•
4 virtual adjustable threshold switches per analog input
from which a virtual user-configurable digital input is set
or reset
•
The digital inputs can also be parameterised as LT inputs
•
Integrated LEDs to indicate a fault (yellow) and alarm
(red)
• Connection using removable spring-type terminals
•
Conductor cross-sections max. 1.5 mm² flexible
• Dimensions WxHxD: 26x130x125 mm
•
Installation on a 35 mm top hat rail in combination with
an expansion module socket
