D Light Aura, User Manual

14 

- GB

GB - 

15

ENGLISH

ENGLISH

NOTE:

Treating the same body part more frequently than recommended does not improve results. Due 

to hormonal and physiological changes or other type, hair follicles, latents can become active. 

Hair removal sessions or occasional maintenance treatment can therefore be necessary.

Individual reaction depends on hair type and biological factors that can affect the hair growth 

cycle. Compared to the recommended epilation program, some people may react faster or 

slower.

The appliance is not effective on very clear hair, on naturally white, gray, light blond and red hair 

(see color scale on the packaging). If the hairs of your body are one of these colors, the device 

will not be effective.

INSPECTION BEFORE USE

ENERGY LEVEL

he appliance can be set to 5 energy levels, from 1 (the lowest) 

to 5 (the highest), represented by the 5 lines arranged like a fan 

on the status display (1). The energy increases and decreases 

repeatedly pressing energy level button (10) Increasing the 

power of treatment increases the effectiveness of the CIA, but 

also  possible  side  effects,  it  is  advisable  to  perform  a  patch 

test to identify the appropriate energy level according to proper 

tolerance.

NUMEBER OF DISPOSABLE SPOTS

The meter reads the number of disposable spots available to the 

light inserted. Spot counting is stored in an internal chip in the 

light, then dismantling and reassembling the light, the count is 

never lost, but reparts from the point where it was left. Each light 

has its own count, when the light is 0, it must be replaced.

TEMPERATURE LOCK

In order to avoid burns, if the temperature is more than protective 

temperature of the device during the treatment, the protection 

lock icon (as shown) will show on the display and the device will 

stop working to send pulse.

HOW TO PERFORM A PATCH TEST

Because the skin tone varies from area to another, you should perform a patch test to each 

body area to be treated. First check your skin tone comparing it with the skin color chart on the  

instruction manual and packaging.

Identify a small area to be treated.

Shave the area to be treated.

After having set to the lowest level, apply the handpiece to the area and emit the first pulse. 

If you do not feel any kind of discomfort, increase the energy to the next level, move the 

handpiece to the adjacent part of skin and emit a new flash. 

Increase the energy level on every part of the next skin until reaching the highest level (but it must 

remain bearable depending on skin type). During treatment it is possible (and normal) to feel a 

warm sensation on the skin. If there is a feeling of discomfort, it means that the highest energy 

level endured the previous one.

After 24 hours check the area: the persistence of redness indicates that the skin tolerated 

the highest energy level on the previous one. Although it is extremely rare, if hypersensitivity 

persists for more than 24 hours, it is advisable to consult a physician.

CAUTION:

 The energy directly delivered affects the result, but because of the principle

treatment, you should not exceed the maximum threshold that your skin is able to tolerate. This 

threshold is normally high for light skins and low for dark skins, because the presence of melanin 

darkens the skin, increases heat production. Do not exceed the highest threshold that your skin 

can tolerate without any kind of discomfort.

MAINTANANCE

CLEANING AND CONSERVATION

It is recommended that you clean the Flash window after each epilation session:

Switch off the appliance by holding the ignition button down (9) and disconnect the Power plug 

(6)

Gently wipe the flash window of the device (12) with a clean dry cloth. For proper cleaning of 

the flash area, it is highly recommended to use Kera Flux detergent

Store the appliance in a cool dry place, away from heat and water sources.

When the light is empty, the counter reaches zero.

LAMP PROTECTION ERROR

If you forcibly pull the lamp out when the appliance is still working 

or on standby, the protection lock icon (as shown) will shown on 

the display and the device will stop working to send pulse.