manualshive.com logo in svg

D-Link DFL-1600 - Security Appliance, User Manual

Introducing the D-Link DFL-1600 - a powerful Security Appliance designed to safeguard your network. Unlock the full potential of this device by downloading the comprehensive User Manual for free from our website. Get detailed instructions, tips, and troubleshooting advice to maximize your network security.

Share
Download
background image

attempting to flow is 4 Mbps. Since the pipe limit is 2 Mbps, the actual flow will be close to 1 Mbps
in each direction.

Raising the total pipe limit to 4 Mbps will not solve the problem since the single pipe will not know
that 2 Mbps of inbound and 2 Mbps of outbound are the intended limits. The result might be 3 Mbps
outbound and 1 Mbps inbound since this also adds up to 4 Mbps.

Using Two Separate Pipes Instead

The recommended way to control bandwidth in both directions is to use two separate pipes, one for
inbound and one for outbound traffic. In the scenario under discussion each pipe would have a 2
Mbps limit to achieve the desired result. The following example goes through the setup for this.

Example 10.2. Limiting Bandwidth in Both Directions

Create a second pipe for outbound traffic:

Command-Line Interface

gw-world:/> add Pipe std-out LimitKbpsTotal=2000

Web Interface

1.

Go to Traffic Management > Traffic Shaping > Pipes > Add > Pipe

2.

Specify a name for the pipe, for example std-out

3.

Enter 2000 in Total textbox

4.

Click OK

After creating a pipe for outbound bandwidth control, add it to the forward pipe chain of the rule created in the
previous example:

Command-Line Interface

gw-world:/> set PipeRule Outbound ForwardChain=std-out

Web Interface

1.

Go to Traffic Management > Traffic Shaping > Pipe Rules

2.

Right-click on the pipe rule that was created in the previous example and choose Edit

3.

Under the Traffic Shaping tab, select std-out in the Forward Chain list

4.

Click OK

This results in all outbound connections being limited to 2 Mbps in each direction.

10.1.5. Creating Differentiated Limits Using Chains

In the previous examples a static traffic limit for all outbound connections was applied. What if the
aim is to limit web surfing more than other traffic? Assume that the total bandwidth limit is 250
kbps and 125 kbps of that is to be allocated to web surfing inbound traffic.

The Incorrect Solution

Two "surfing" pipes for inbound and outbound traffic could be set up. However, it is not usually
required to limit outbound traffic since most web surfing usually consists of short outbound server

10.1.5. Creating Differentiated Limits
Using Chains

Chapter 10. Traffic Management

456

Summary of Contents for DFL-1600 - Security Appliance









































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for DFL-1600 - Security Appliance

X-Z Lab IoT-Cloud 2.0 User Manual preview
IoT-Cloud 2.0
Brand: X-Z Lab Pages: 3
IBASE Technology FWA6504 User Manual preview
FWA6504
Brand: IBASE Technology Pages: 16
SonicWALL TZ 170 Series Quick Start Manual preview
TZ 170 Series
Brand: SonicWALL Pages: 12
Pulse Secure PSA3000 Hardware Manual preview
PSA3000
Brand: Pulse Secure Pages: 42
Pulse Secure PSA7000 Hardware Manual preview
PSA7000
Brand: Pulse Secure Pages: 52
Norman NetworkProtection Administrator'S Manual preview
NetworkProtection
Brand: Norman Pages: 79
Global Technology Associates GB-800 Brochure preview
GB-800
Brand: Global Technology Associates Pages: 2

Brands by name

Popular brands

Load more brands