background image

D-Link Switch User Manual 

1

 

About This Guide 

This guide provides instructions to install the D-Link DGS-1026MP 26-Port Unmanaged PoE Gigabit Switch. 
 

Terms/Usage 

In this guide, the term “Switch” (first letter capitalized) refers to the DGS-1026MP, and “switch” (first letter lower 

case) refers to other Ethernet switches. Some technologies refer to the terms “switch”, “bridge” and “switching 

hubs” interchangeably, and all are commonly accepted for Ethernet switches. 
 

 

NOTE

  indicates important information  to use 

the device properly. 

 

 

CAUTION

 indicates potential property damage 

or personal injury. 

 

Copyright and Trademarks 

Information in this document is subjected to change without notice. 
© 2016 D-Link Corporation. All rights reserved. 
Reproduction in any manner whatsoever without the written permission of D-Link Corporation is strictly 

forbidden. 
Trademarks used in this text: D-Link and the D-LINK logo are trademarks of D-Link Corporation. 
Other trademarks and trade names may be used in this document to refer to either the entities claiming the 

marks and names or their products. D-Link Corporation disclaims any proprietary interest in trademarks and 

trade names other than its own. 

 

 

Summary of Contents for DGS-1026MP














Reviews: