D-Link DGS-1026MP User Manual Download | Manualshive

Page: 9 / 13

background image

D-Link Switch User Manual

7

Connect to a Hub or Switch

Use a straight or crossover cable to connect the Switch to another switch or hub.

Figure 9 – Connecting the Switch to another switch or hub

Connect to a Network Backbone or Server

Use any port on the device to connect the Switch to a network backbone or network server. When linking to

a 1000BASE-T device, the port operates in full-duplex mode.

Figure 10 – Connecting the Switch to another switch or hub

«
...
7
8
9
10
11
...
»

Summary of Contents for DGS-1026MP














Reviews:

No comments

Related manuals for DGS-1026MP

Brand: Manhattan Pages: 2

Brand: NETGEAR Pages: 2

Brand: Nobile Pages: 2

Signature ANTENNA GENIUS 8x2 v2 PLUS

Brand: 4O3A Pages: 57

TigerAccess SMC7824M/FSW

Brand: SMC Networks Pages: 2

Brand: Cabletron Systems Pages: 54

Brand: TESmart Pages: 4

Brand: Black Box Pages: 4

Brand: Minicom DX Pages: 36

Brand: QSFPTEK Pages: 8

ScatterBox POE308

Brand: System Q Pages: 2

OmniAccess 6000

Brand: Alcatel-Lucent Pages: 76

Brand: AVCOMM Pages: 2

Brand: JUKI Pages: 2

Brand: N-Tron Pages: 15

Brand: CoolGear Pages: 8

Brand: NETGEAR Pages: 2

NetDirector B064-016-02-IPH

Brand: Eaton Pages: 12

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands