DGS-3100 Gigabit Ethernet Switch Manual
60
he Root Bridge. If it turns out that your switch has the
maxhops <value 1-20>
−
The number of hops between devices in a
ridge protocol data unit)
. Each switch on the hop
unt by one until the value reaches zero.
The Switch will then discard the BDPU packet and the information
n 1 and 20.
e <value 1-10>
−
The user may set the time interval between
nsmission of configuration messages by the root device in STP,
or by the designated router in RSTP, thus stating that the Switch is
still functioning. The value may be between 1 and 10 seconds. The
default value is 2 seconds.
In MSTP, the spanning tree is configured by port and therefore, the
hellotime must be set using the configure stp ports command for
.
<value 4-30>
−
The maximum amount of time (in
the forwarding of STP BPDU
from other network devices when STP is disabled on the
will start sending its own BPDU to all other switches for permission
to become t
lowest Bridge Identifier, it will become the Root Bridge. The user
is
may choose a time between 6 and 40 seconds. The default value
20.
spanning tree region before the BPDU (b
packet sent by the Switch will be discarded
count will reduce the hop co
held for the port will age out. The value may be betwee
The default is 20.
hellotim
tra
switches utilizing the Multiple Spanning Tree Protocol
forwarddelay
seconds) that the root device will wait before changing states. The
value may be between 4 and 30 seconds. The default is 15 seconds.
fbpdu [enable | disable]
−
Allows
packets
Switch. The default is enable.
Restrictions Only
administrator-level users can issue this command.
Exampl
To configure STP
ps of 15:
GS3100# config stp maxage 18 maxhops 15
uccess.
DGS3100#
e usage:
with maxage 18 and maxho
D
S
config stp ports
Purpose
To setup STP on the port level.
Syntax
config stp ports <portlist> {externalcost [auto | <value 1-
200000000>] | edge [true | false] | p2p [true | false | auto ] | state
[enable | disable]}
Description The
config stp ports
command configures STP for a group of ports.
Parameters
<portlist>
−
Specifies a range of ports to be configured. The port list
is specified by listing the lowest switch number and the beginning
ort number on that switch, separated by a colon. Then the highest
r, and the highest port number of the range (also
colon) are specified. The beginning and end of the
port list range are separated by a dash. For example, 1:3 specifies
ch number 1, port 3. 2:4 specifies switch number 2, port 4. 1:3-
cifies all of the ports between switch 1, port 3 and switch 2,
port 4
−
in numerical order.
p
switch numbe
separated by a
swit
2:4 spe
Summary of Contents for DGS-3100 SERIES
