61
externalCost
−
Defines a metric that indicates the relative cost of
forwarding packets to the specified port list. Port cost can be set
automatically or as a metric value. The default value is auto.
rwarding packets
cy.
fault port cost: 100Mbps port = 200000. Gigabit port =
1-200000000>
- Defines a value between 1 and
200000000 to determine the external cost. The lower the
number, the greater the probability the port will be chosen to
forward packets.
hellotime <value 1-10>
−
The time interval between transmission of
messages by the designated port, to other devices on
AN, thus stating that the Switch is still functioning. The
value may be between 1 and 10 seconds. The default is 2 seconds.
e
designates the port as an edge port. Edge
create loops, however an edge port can lose edge port
pology change creates a potential for a loop. An edge
port normally should not receive BPDU packets. If a BPDU packet is
loses edge port status.
false
indicates that
tatus.
to]
–
true
indicates a point-to-point (P2P) shared
e similar to edge ports however they are restricted
must operate in full-duplex. Like edge ports, P2P
a forwarding state rapidly thus benefiting from
of
false
indicates that the port cannot have p2p
ort to have p2p status whenever possible
2p status were true. If the port cannot
s status (for example if the port is forced to half-duplex
eration) the p2p status changes to operate as if the p2p value
were
false
. The default setting for this parameter is
auto
.
[enable | disable]
−
Allows STP to be enabled or disabled for
cified in the port list. The default is enable.
•
auto
– Automatically sets the speed for fo
ied port(s) in the list for optimal efficien
to the specif
De
20000.
•
<value
configuration
the bridged L
edge [true | false]
–
tru
ports cannot
status if a to
received it automatically
the port does not have edge port s
p2p [true | false | au
link. P2P ports ar
in that a P2P port
ports transition to
RSTP. A p2p value
status.
auto
allows the p
and operate as if the p
maintain thi
op
state
the ports spe
Restrictions Only
trator-level users can issue this command.
adminis
Example usage:
To configure STP
econds and state enable for ports 1-5 of module 1.
1:1-1:5 externalCost 19 hellotime 5
with path cost 19, hellotime set to 5 s
DGS3100# config stp ports
state enable
Success.
DGS3100#
config stp version
Purpose
et the version of STP on the Switch.
To globally s
Syntax
config stp version [mstp | rstp | stp]
Description
d sets the version of the spanning
on the Switch.
The
config stp version
comman
tree to be implemented
Parameters
ltiple Spanning Tree Protocol (MSTP) globally on
mstp
– Sets the Mu
the Switch.
Summary of Contents for DGS-3100 SERIES
